rear wheel bearing

[Meir]

Originally Posted by derfo

Hello Meir
I just seen your post. One place you could have a look is Pelican Parts. I went to their site and they have it all explained there. They have one photo showing the bearing just how yours is with a two prong puller dragging it off.

yes.
thank you very much for the reply.
you are probably referring to this picture:






i was kind of hoping to pick something local and finish it today.
i got few generic pullers, butt none of them worked.
i have a transmissions rebuild shop close to my office. i will probably stop there tomorrow, and see if they could pull it out for me.

[Meir]

looked at the pelican website, and they do not offer this puller for sale.
i wonder if something like that might work.

http://www.amazon.com/ATD-Tools-3056-Bar-Type-Separator/dp/B004IQ8RMU/ref=sr_1_1?ie=UTF8&qid=1450306748&sr=8-1&keywords=bearing+puller

[derfo]

Originally Posted by Meir

looked at the pelican website, and they do not offer this puller for sale.
i wonder if something like that might work.

http://www.amazon.com/ATD-Tools-3056-Bar-Type-Separator/dp/B004IQ8RMU/ref=sr_1_1?ie=UTF8&qid=1450306748&sr=8-1&keywords=bearing+puller

It looks to me like there are no hooks. I don't think those round disc's would be up to it, also don't think they would fit either and it all looks a bit lightweight as well. Take your hub to the place near you and see what they have got first.

[Meir]

Originally Posted by derfo

It looks to me like there are no hooks. I don't think those round disc's would be up to it, also don't think they would fit either and it all looks a bit lightweight as well. Take your hub to the place near you and see what they have got first.

you are probably right.
i think this one will make a better fit for this job.

http://www.amazon.com/OTC-4534-Multipurpose-Bearing-Pulley/dp/B00061SM9E/ref=pd_bxgy_263_img_2?ie=UTF8&refRID=1FERVKZW75R1XCQ0RGE4

added to my amzon wishlist, as im sure i will have to do this job again one day

[Deadeye]

Originally Posted by Meir

looked at the pelican website, and they do not offer this puller for sale.
i wonder if something like that might work.

Amazon.com: ATD Tools 3056 Bar-Type Puller/Bearing Separator Set in Molded Storage and Carrying Case - 5 Ton Capacity: Automotive

The tool pictured in this post is what you need to start the race off. Then a 2 or 3 arm puller or a press to finish the job.

[rah rah 986]

I replaced the front bearings last week on my Honda Odyssey. Both hubs came off with the inner race, just like yours. I found a tip that suggested to use a dermal tool with a metal cutting wheel and make a cut across the race about an eighth of an inch deep, in two or three places. Try to cut as deep as you can without cutting through to the hub. Once you have scored the race, take a chisel, setting it into the groove that you have cut. A couple good wacks with a hammer will break it through completely. In my case, one groove was enough to loosen the bearing enough to slide it off. If necessary, you may have to cut a second or third groove. This technique was easy and worked like a charm.

[rah rah 986]

Here is what the cut should look like

[Meir]

Originally Posted by rah rah 986

Here is what the cut should look like

that is a very good idea.

[Meir]

Success!
guys, thank you very much for your comments.
after posting my comments, and having a cold drink (it's 87 degrees today), i went back to the shop, and try something else.
i took parts from two different pullers, and created a new one.
i had to modify it a bit, by grinding the arms.



once i got it moving, i had the space to go in with the 3 hands puller, just like Deadeye suggested.

[Gelbster]

Meir,
You seem to be getting deeper into the mechanical bowels of the Boxster with each post !Well done and thanks for sharing.
So let me anticipate one of your future posts and suggest a better puller ?
Eventually you are going to need to replace a bearing and maybe 2nd gear in the 6 speed gearbox. For that you need a puller that coincidentally would work on the hub but is also about the only one that fits for the gearbox.It is a Kukko slender arm puller KK 20-10-S
http://www.amazon.com/Kukko-KK20-10-Slender-Adjusting-Puller/dp/B00D8VL11A
A cheaper alternative that may work is:
12 PC New Car Repair Tools Universal Puller Set Two Arms Pulley Remover N008341 | eBay
The 'dremel-tool' technique mentioned earlier certainly works but requires great care.
When fitting the new bearing, remember the freezer/oven technique to avoid damage.
Are you doing the CV boots also?
Keep us posted.

[Meir]

Originally Posted by Gelbster

Meir,
You seem to be getting deeper into the mechanical bowels of the Boxster with each post !Well done and thanks for sharing.
So let me anticipate one of your future posts and suggest a better puller ?
Eventually you are going to need to replace a bearing and maybe 2nd gear in the 6 speed gearbox. For that you need a puller that coincidentally would work on the hub but is also about the only one that fits for the gearbox.It is a Kukko slender arm puller KK 20-10-S
http://www.amazon.com/Kukko-KK20-10-Slender-Adjusting-Puller/dp/B00D8VL11A
A cheaper alternative that may work is:
12 PC New Car Repair Tools Universal Puller Set Two Arms Pulley Remover N008341 | eBay
The 'dremel-tool' technique mentioned earlier certainly works but requires great care.
When fitting the new bearing, remember the freezer/oven technique to avoid damage.
Are you doing the CV boots also?
Keep us posted.

thank you very much Gelbster.
added the tool to my wish list.
bearing are seating in the freezer for few days now
i rebuilt the axles (boots and joints) about 15k miles ago, and they still look good.
i hope to finish it tomorrow, and find the time to make a nice write up.
i was very surprised to see that there is no instructions or videos online for this procedure, using the SIR tool.
its very easy once you figure it out, but it is some what of a jigsaw Puzzle.

[Meir]

Hello guys.
due to lack of time, i never got around to update this thread, and do the write-up as i wanted to.
i will try to add some pictures and explanation to the thread, and maybe one day will find the time to make a PDF document of the full procedure.