Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Performance and Technical Chat

Post Reply
 
LinkBack Thread Tools Display Modes
Old 09-10-2014, 10:06 PM   #1
Registered User
 
Join Date: Sep 2013
Location: uk, notts
Posts: 141
radiator cooling fan resistor values?

Does anyone know the impedance and wattage of the fan resistor. There can only be two factors, so was looking to buy a pair of ceramic high wattage resistors to do the job and save me dollars on the expensive OE part.

Thanks

jimk04 is offline   Reply With Quote
Old 09-12-2014, 02:11 PM   #2
1999 base
 
Meir's Avatar
 
Join Date: Dec 2011
Location: Coral Springs FL
Posts: 1,617
Garage
Quote:
Originally Posted by jimk04 View Post
Does anyone know the impedance and wattage of the fan resistor. There can only be two factors, so was looking to buy a pair of ceramic high wattage resistors to do the job and save me dollars on the expensive OE part.

Thanks
i have a brand new resistor in my garage, so i can measure the resistance for you.
not sure how can i measure wattage.
Meir is offline   Reply With Quote
Old 09-12-2014, 04:43 PM   #3
Certified Boxster Addict
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 7,669
Quote:
Originally Posted by Meir View Post
i have a brand new resistor in my garage, so i can measure the resistance for you.
not sure how can i measure wattage.
Measure the Resistance; then calculate wattage by;

Watts = (voltage*voltage)/Resistance where voltage is nominally 12 volts.

Watts = 144/Resistance


Reference: How To Calculate Resistor Wattage
__________________
1999 996 C2 - sold - bought back - sold for more
1997 Spec Boxster BSR #254
1979 911 SC
POC Licensed DE/TT Instructor
thstone is offline   Reply With Quote
Old 09-12-2014, 05:57 PM   #4
On the slippery slope
 
JayG's Avatar
 
Join Date: Mar 2014
Location: Austin and Palm Springs
Posts: 3,793
Garage
The physical size will also give you some idea of the resistor wattage

I believe Tom's calculation will give you the wattage draw based on the voltage.
You need to have a resistor that is rated higher than the actual draw or It will burn up
__________________
2004 Boxster S 6 speed - DRL relay hack, Polaris AutoTop DIY
2004 996 Targa Tip
Instructor - San Diego region
2014 Porsche Performance Driving School
2020 BMW X3, 2013 Ram 1500, 2016 Cmax, 2004 F-150 "Big Red"

Last edited by JayG; 09-14-2014 at 06:37 AM.
JayG is offline   Reply With Quote
Old 09-13-2014, 11:56 PM   #5
Registered User
 
Join Date: Sep 2013
Location: uk, notts
Posts: 141
That's great if you could measure it thanks.
jimk04 is offline   Reply With Quote
Old 09-19-2014, 11:30 AM   #6
1999 base
 
Meir's Avatar
 
Join Date: Dec 2011
Location: Coral Springs FL
Posts: 1,617
Garage
just got back from a road trip.
will measure and post results this weekend.
Meir is offline   Reply With Quote
Old 09-19-2014, 01:25 PM   #7
On the slippery slope
 
JayG's Avatar
 
Join Date: Mar 2014
Location: Austin and Palm Springs
Posts: 3,793
Garage
from what I could find on the web, it is around .5 ohm and 100 Watt
It would be interesting to see if your measurements show that

BTW, the resistor value will determine how fast the fan runs
__________________
2004 Boxster S 6 speed - DRL relay hack, Polaris AutoTop DIY
2004 996 Targa Tip
Instructor - San Diego region
2014 Porsche Performance Driving School
2020 BMW X3, 2013 Ram 1500, 2016 Cmax, 2004 F-150 "Big Red"
JayG is offline   Reply With Quote
Old 09-20-2014, 08:42 AM   #8
1999 base
 
Meir's Avatar
 
Join Date: Dec 2011
Location: Coral Springs FL
Posts: 1,617
Garage
Ok
3 wires coming out of the resistor.
Green/white. Goes from resistor to fan.
Green goes from resistor to connector.
White goes from resistor to connector.
I believe the green wire and the white wire are 12 volt input for the two fan speeds.
The green with the white stripe, is the output to the fan.
Another black wire ( ground) goes from connector to fan.
Measured tresistance between the green/ White, to the other Wires.
Between green/white and green -0.8 ohm.
Between green/white and white - 0.2 ohm.
Meir is offline   Reply With Quote
Old 09-21-2014, 08:32 AM   #9
Registered User
 
DennisAN's Avatar
 
Join Date: Mar 2014
Location: Boise, ID
Posts: 111
Be careful to "zero" your meter when dealing with such tiny ohm values. It is possible the measured values in the above post are in error by 0.2 ohms each, when the real values would be 0.0 ohms (i.e. a wire) and 0.6 ohms.

What YEAR is the OP's car? The resistor value appears to vary between model years.

The FSM for 2000+ cars shows only a single resistor per fan motor. Both are shown as 0.55 ohms on the schematic diagram.

To calculate the wattage you have to account for the resistance of both the resistor and the fan motor as they are operating in series to ground. Once you have the overall amperage, you can then backtrack and apply ohm's law to the resistor itself to determine its minimum wattage rating.
__________________
Base 2000 986, beater 1996 Miata, 2011 Suzuki SX4 AWD
Feline mechanics Condoleezza and Dukie

Last edited by DennisAN; 09-21-2014 at 08:43 AM.
DennisAN is offline   Reply With Quote
Old 09-21-2014, 01:18 PM   #10
Registered User
 
Join Date: Sep 2013
Location: uk, notts
Posts: 141
Thanks for all the input.

It seems this isn't quite as simple as I thought. What with the twin values and 3 wires!
But this may be worth pursuing, as £65 GBP seems a lot for a resistor period.!
Maybe we can fathom it!
jimk04 is offline   Reply With Quote
Old 09-21-2014, 06:06 PM   #11
On the slippery slope
 
JayG's Avatar
 
Join Date: Mar 2014
Location: Austin and Palm Springs
Posts: 3,793
Garage
Quote:
Originally Posted by DennisAN View Post
Be careful to "zero" your meter when dealing with such tiny ohm values. It is possible the measured values in the above post are in error by 0.2 ohms each, when the real values would be 0.0 ohms (i.e. a wire) and 0.6 ohms.

What YEAR is the OP's car? The resistor value appears to vary between model years.

The FSM for 2000+ cars shows only a single resistor per fan motor. Both are shown as 0.55 ohms on the schematic diagram.

To calculate the wattage you have to account for the resistance of both the resistor and the fan motor as they are operating in series to ground. Once you have the overall amperage, you can then backtrack and apply ohm's law to the resistor itself to determine its minimum wattage rating.
That makes sense, that the measured values are off by ~.2 ohm. I believe that on HIGH, the fan get the full 12v and on low it is lowered by the resistor in series

Now the fuse for each fan is 40 amp, if it was a full draw of 40 amps, it would be ~440 watts

12 volts through a .55 ohm resistor is ~260 watts or ~21 amps.

My guess is that the low speed resistor is ~ 300 watts rating if .55 ohm and ~250 watts if .8 ohm

What gets interesting is that the voltage drop on a .55 ohm resistor with a 12 v source is ~11.5 volts. That leaves ~.5 volt to the fan

If we go with .8 ohm as measured, then the current is 15 amps and the voltage drop would be 8.25 volts leaving 3.75 for the fan. This sounds more realistic than .5 volts to the fan

if the actual voltage is higher, say 13 volts than the voltage to the fan will increase slightly and the fan speed would be higher

Maybe a measurement of the voltage after the resistor would shed some light on this

Of course if my calculations are wrong, then fo-ged-about-it
__________________
2004 Boxster S 6 speed - DRL relay hack, Polaris AutoTop DIY
2004 996 Targa Tip
Instructor - San Diego region
2014 Porsche Performance Driving School
2020 BMW X3, 2013 Ram 1500, 2016 Cmax, 2004 F-150 "Big Red"
JayG is offline   Reply With Quote
Old 10-15-2016, 09:24 AM   #12
Registered User
 
Join Date: Feb 2016
Location: Slovenia
Posts: 1
Quote:
Originally Posted by JayG View Post
Now the fuse for each fan is 40 amp, if it was a full draw of 40 amps, it would be ~440 watts

12 volts through a .55 ohm resistor is ~260 watts or ~21 amps.

My guess is that the low speed resistor is ~ 300 watts rating if .55 ohm and ~250 watts if .8 ohm

What gets interesting is that the voltage drop on a .55 ohm resistor with a 12 v source is ~11.5 volts. That leaves ~.5 volt to the fan
Sorry to revive an old thread, but the above is fundamentally wrong as it neglects the fact, that the electric motor has an impedance as well.

If we assume that the motor draws full 40A at 12V, it's impedance would be 0.3 Ohm. But that would be unreasonable, so if the motor drew 20A, the impedance it would be 0.6 Ohm. I would 'guess' that the actual impedance is somewhere in the middle - in fact, I'd say it's equal to the resistor, i.e. 0.55 Ohm.

Since the resistor for low speed operation is connected in series with the motor, the total impedance is 1.1 Ohm, meaning that the amperage draw is 11A and the resulting voltage drop is 6V, leaving another 6V for the fan, cutting the fan speed in half.

The power dissipation on the resistor is 66W, so a 100W 0.55 Ohm resistor should be just fine.
danci1973 is offline   Reply With Quote
Old 10-15-2016, 10:39 AM   #13
Registered User
 
Join Date: May 2014
Location: S.California
Posts: 2,027
If you plug in the Porsche part number to an Interchange parts list - what comes up?
Part number is :996.616.101.00
This link may help?
Step by step DIY with pics radiator ballast resistor replacement - Rennlist Discussion Forums
http://www.renntech.org/forums/topic/37254-radiator-fan-question/
There is a Hack -buried in this thread:
http://www.renntech.org/forums/topic/20479-radiator-cooling-fan-question-yup-i-searched/
Just google Porsche hack Ballast Resistor fan cooling radiator or similar.

Last edited by Gelbster; 10-15-2016 at 10:45 AM.
Gelbster is offline   Reply With Quote
Old 10-25-2016, 12:50 PM   #14
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Based on a thread that I can't find now, I ordered the following one:

https://www.amazon.com/gp/product/B008MLL3JQ/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1

Which is 100 watts .5 ohms and seems to match up with others in this thread. I haven't installed it yet, I am watching the other thread to see what happens if you just bypass the resistor...
steved0x is offline   Reply With Quote
Old 10-25-2016, 01:00 PM   #15
Registered User
 
Join Date: May 2014
Location: S.California
Posts: 2,027
Based on Danci's calculations, that seems a good choice of specifications. Best of all it avoids the Porsche Parts tax - so keep us informed of the success (or otherwise?) of your experiment.These resistors ae $1.50 on Fleabay but.......


Last edited by Gelbster; 10-25-2016 at 01:03 PM.
Gelbster is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 10:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page