Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 01-03-2017, 01:17 PM   #1
Registered User
 
Join Date: Sep 2016
Location: New York
Posts: 99
Arrow RPM's For Performance

I'm wondering what would be the RPM range that allows engine to come alive without approaching red line

2002 986 5 spd [ not S]

I just had some pro active work done [ IMS , RMS , Clutch , flywheel ] and would like to
start driving car a bit more vigorously not racing just letting it go occasionally

I have been shifting mostly between 3- 4k rpm's Have gone into 5k and felt more power
1st gear won't need too much higher than 3 k [ thats just my feel for it ]
2-5 would be more flexible rev wise

mfm22 is offline   Reply With Quote
Old 01-03-2017, 01:56 PM   #2
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
On track I like to shift around 6200 unless I am winding it out like at Sebring where if I shift up a hear I would have to shift right back, but even then I don't like to go above 6500.

That doesn't answer your question though. Do a few pulls in 3rd and 4th and feel when it comes alive, around 4000+? 4500? As long as you don't shift in such a way the you are below 4000/4500 in the new gear, you should be in the power band and liking the performance 6000/6200 has been working for me and is not too hard on the engine. On the street I shift around 3000
steved0x is offline   Reply With Quote
Old 01-03-2017, 01:57 PM   #3
Certified Boxster Addict
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 7,669
In a racing weekend, I shift near/at redline around 400 times (basically every upshift). Probably 10 shifts bounce off of the rev limiter. Then I do this 15 weekends a year; so 6,000 shifts at redline per year for the past two years. And I do this on a completely stock 2.5L engine with original IMS bearing and 97,000 miles.

Of course, this level of use is hard (very hard) on the engine and I expect its life expectancy to be greatly reduced (which is why I have a spare engine in my workshop).

But the point I want to make is that these engines are pretty tough and durable (despite what you might read) and running your engine to redline a few times a month isn't going to hurt anything or reduce its life expectancy.

With that being said and to directly answer your question, the engine will feel most alive from 4,000 to 6,000 rpm without placing any undue stress on the motor.
__________________
1999 996 C2 - sold - bought back - sold for more
1997 Spec Boxster BSR #254
1979 911 SC
POC Licensed DE/TT Instructor

Last edited by thstone; 01-03-2017 at 02:00 PM.
thstone is offline   Reply With Quote
Old 01-03-2017, 02:02 PM   #4
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Tom what is the redline on the 2.5L, is it 6500 or 6800? On the 2.7/3.2 It is 7200 or 7300, which I have hit a few times, then I read something by Jake or Brad Roberts (apologies that I can't remember) that said on the 2.7/3.2 engines to keep to the 2.5 redline for longevity. Plus I am a wuss...

Last edited by steved0x; 01-03-2017 at 02:48 PM.
steved0x is offline   Reply With Quote
Old 01-03-2017, 02:43 PM   #5
Ben-Auto-Design
 
Ben006's Avatar
 
Join Date: Oct 2014
Location: French Riviera
Posts: 827
Quote:
Originally Posted by thstone View Post
and running your engine to redline a few times a month isn't going to hurt anything or reduce its life expectancy.
One redline a day, keeps the carbon away!
__________________
ASE certified Automotive Master Technician.
Porsche Tech in France.
www.benautodesign.fr
Ben-Auto-Design : Performance parts for 9X6 / 9X7
1982 928 S Euro
Ben006 is offline   Reply With Quote
Old 01-03-2017, 03:20 PM   #6
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Does anyone have a stock engine HP/torque chart handy?
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 01-03-2017, 03:24 PM   #7
Registered User
 
Join Date: May 2016
Location: Northville, MI
Posts: 249
Quote:
Originally Posted by mfm22 View Post
I'm wondering what would be the RPM range that allows engine to come alive without approaching red line

2002 986 5 spd [ not S]

I just had some pro active work done [ IMS , RMS , Clutch , flywheel ] and would like to
start driving car a bit more vigorously not racing just letting it go occasionally

I have been shifting mostly between 3- 4k rpm's Have gone into 5k and felt more power
1st gear won't need too much higher than 3 k [ thats just my feel for it ]
2-5 would be more flexible rev wise
Dude, sorry to be insulting but you do know you bought a sports car? Don't drive it like grandpa (no offense, i'm a grandpa myself) but if I never wanted to go above 5k I would drive my wife's SUV.
There's also many threads that talk about IMS failure in cars that never get "driven" so you are not doing your engine any favors. Revving a car is not bad for it, don't slam the clutch and accelerate briskly and you and the car will be smiling.
bwdz is offline   Reply With Quote
Old 01-03-2017, 05:52 PM   #8
Registered User
 
kk2002s's Avatar
 
Join Date: Sep 2012
Location: S. New Jersey
Posts: 1,239
Garage
I cruise at 3k. Non performance driving shift after 4k. With an S anything after 4k there is decent acceleration and engine breaking
If you want to feel the performance take a highway entrance ramp in 2nd to 6k+ then 3rd to 6k+ and you are in triple digits
__________________
2002 S - old school third pedal
Seal Grey
kk2002s is offline   Reply With Quote
Old 01-04-2017, 04:34 AM   #9
Registered User
 
Join Date: Dec 2016
Location: Clifton, NJ
Posts: 1,135
Lets be real, its not a very powerful car. There is never really a big surge of acceleration.

Rev it to whatever you want (hell, hit fuel cutoff if you feel like it) and is appropriate for the conditions.
Quadcammer is offline   Reply With Quote
Old 01-04-2017, 04:54 AM   #10
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Quote:
Originally Posted by Finnegan View Post
Does anyone have a stock engine HP/torque chart handy?
From the 2000 Owner's manual:


steved0x is offline   Reply With Quote
Old 01-04-2017, 05:23 AM   #11
Motorist & Coffee Drinker
 
78F350's Avatar
 
Join Date: Jul 2014
Location: Oklahoma
Posts: 3,653
Garage
Most importantly, warm the car up to normal operating temperature before driving it hard. The owner's manual says drive it for 5 minutes before revving above 4,200 RPM.



I'd say run it until the temperature gauge has risen to normal operating range and become stable, then have no fear of taking it to 6,000+ and occasionally to the limiter. The engine computer (DME) is designed to prevent the engine from being revved above it's safe range during upshifts and the Tiptronic transmissions will not permit the engine to be put in a condition that will allow an overspeed even in downshifting. The only way that you can exceed the safe operating RPM is to downshift a manual transmission while you are near the maximum range.
__________________
I am not an attorney, mechanic, or member of the clergy. Following any advice given in my posts is done at your own peril.
78F350 is offline   Reply With Quote
Old 01-04-2017, 09:10 AM   #12
Track rat
 
Topless's Avatar
 
Join Date: Nov 2006
Location: Southern ID
Posts: 3,701
Garage
For performance driving I keep the car between 4k-6.5k rpm. My redline is 7200. Below 4000 the torque curve drops off pretty quickly and banging the rev limiter offers very little for me in most cases. Exiting a corner at 6k, the excess torque often just gets lost in wheel spin. Wheel spin is slow.
__________________
2009 Cayman 2.9L PDK (with a few tweaks)
PCA-GPX Chief Driving Instructor-Ret.
Topless is offline   Reply With Quote
Old 01-04-2017, 12:13 PM   #13
Certified Boxster Addict
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 7,669
Quote:
Originally Posted by steved0x View Post
Tom what is the redline on the 2.5L, is it 6500 or 6800? On the 2.7/3.2 It is 7200 or 7300, which I have hit a few times, then I read something by Jake or Brad Roberts (apologies that I can't remember) that said on the 2.7/3.2 engines to keep to the 2.5 redline for longevity. Plus I am a wuss...
2.5L max rpm is 6700. (986 Specs)

Nothing wussy about it - every driver should take good care of the equipment! But you'll find that those last few hundred rpm's make a difference when you're chasing tenths of a second (or ten feet in a race) ...
__________________
1999 996 C2 - sold - bought back - sold for more
1997 Spec Boxster BSR #254
1979 911 SC
POC Licensed DE/TT Instructor
thstone is offline   Reply With Quote
Old 01-04-2017, 12:46 PM   #14
Registered User
 
911monty's Avatar
 
Join Date: Oct 2014
Location: California Central Coast
Posts: 1,476
Garage
Quote:
Originally Posted by steved0x View Post
From the 2000 Owner's manual:


From a strictly power standpoint, these Dyno charts seem to indicate there is little advantage to shifting beyond 6300 rpm as horsepower and torque are rapidly diminishing beyond that.
911monty is offline   Reply With Quote
Old 01-04-2017, 02:57 PM   #15
Ben-Auto-Design
 
Ben006's Avatar
 
Join Date: Oct 2014
Location: French Riviera
Posts: 827
Well, if you shift later, you'll end up in the next gear at higher RPM and you'll have more power available. From a performance point of view, you shouldn't shift at peak power, but later.
__________________
ASE certified Automotive Master Technician.
Porsche Tech in France.
www.benautodesign.fr
Ben-Auto-Design : Performance parts for 9X6 / 9X7
1982 928 S Euro
Ben006 is offline   Reply With Quote
Old 01-04-2017, 03:18 PM   #16
Registered User
 
Join Date: May 2014
Location: S.California
Posts: 2,027
Quote:
Originally Posted by mfm22 View Post
I'm wondering what would be the RPM range that allows engine to come alive without approaching red line

2002 986 5 spd [ not S]

I just had some pro active work done [ IMS , RMS , Clutch , flywheel ] and would like to
start driving car a bit more vigorously not racing just letting it go occasionally

I have been shifting mostly between 3- 4k rpm's Have gone into 5k and felt more power
1st gear won't need too much higher than 3 k [ thats just my feel for it ]
2-5 would be more flexible rev wise
If you are concerned about damaging the engine with high revs, one issue is balance. You mention "Flywheel" -do you mean DMF or LWFW?
If you mean an aftermarket LWFW then back off before the undamped vibration and natural imbalance spins a bearing. It is all in Search.
If by 'flywheel'you mean DMF, did you check for wear,get theDMF+the clutch balanced ?
When I had my new DMF balanced it required an alarming amount of material removed to balance it perfectly. The clutch pressure plate was O.K. An unbalanced 30+ pound DMF cantilevered out, way beyond the last main bearing is a problem. This too has been discussed (Search)by others much better qualified than me.
Gelbster is offline   Reply With Quote
Old 01-04-2017, 04:28 PM   #17
Registered User
 
Join Date: Sep 2016
Location: Stow, MA
Posts: 918
Garage
The optimal shift point is where the torque delivered to the wheels curve for the current gear crosses the wheel torque curve for the next gear. It is easy to calculate from the gear ratio and torque curves in the owners manual.
__________________
2004 Boxster S Silver - FUNTOY
2002 Boxster Base Guardsy Red - FUNBOX
1987 Caterham Super 7 1700 Supersprint
2009 Mercedes Benz CLK 350 convertible
1941 Dodge Luxury Liner Coupe
Anker is offline   Reply With Quote
Old 01-06-2017, 12:27 PM   #18
Registered User
 
Join Date: Nov 2014
Location: Ocean Springs, Ms.
Posts: 30
I have a '99 base with headers, test pipes, and a Borla exhaust. The front set of cats are gone. I also have a cold air intake system. The rev limiter pings at 6800 rpm.
When I go out for a road trip, or even just around town, I'll wind it up to 6500...often. The engine does not protest. My Porsche mechanic, and my friends with all different models and years of Porsches always say drive it the way F. Porsche intended the car to be driven...with gusto....
I have over a 100k miles on it. It doesn't leak or burn oil, nor any other fluids...either I'm lucky, or everyone is right...I believe maybe for me, both....

One last thing...DO NOT LUG the engine!

tim
timlawton is offline   Reply With Quote
Old 01-06-2017, 02:21 PM   #19
Registered User
 
Join Date: Dec 2016
Location: Norman, OK
Posts: 51
Garage
Quote:
Originally Posted by bwdz View Post
Dude, sorry to be insulting but you do know you bought a sports car? Don't drive it like grandpa (no offense, i'm a grandpa myself) but if I never wanted to go above 5k I would drive my wife's SUV.
There's also many threads that talk about IMS failure in cars that never get "driven" so you are not doing your engine any favors. Revving a car is not bad for it, don't slam the clutch and accelerate briskly and you and the car will be smiling.
That's insulting to SUVs

I love getting the Escalade above 5000.

Agree completely on cutting loose. I'm still new to Porsches but I know it has to hold 9 quarts of oil for a reason.

Sent from my SM-G920T using Tapatalk
mattluttrell is offline   Reply With Quote
Old 01-06-2017, 02:23 PM   #20
Registered User
 
Join Date: Dec 2016
Location: Norman, OK
Posts: 51
Garage
Not to hijack this thread, I hit redline once in mine and it felt like I hit an ignition rev limiter. Is that what happened or were my valves floating (I hope not)?

Sent from my SM-G920T using Tapatalk

mattluttrell is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 05:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page