Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 01-01-2017, 07:40 AM   #1
Registered User
 
Join Date: Aug 2015
Location: Brandon MB
Posts: 51
Replace Non-leaking RMS?

I'm undecided and looking for some thoughts.

I'm in the process of replacing the IMS bearing on my 01S. It's got a little over 30,000 miles on it and I'm doing the IMS for peace of mind. Before pulling the car apart I was certain I would be replacing the RMS as well and purchased the updated one.

The original RMS is still in place. When I pulled off the flywheel there was no evidence of any oil leaking at all. If it weren't for a little bit of clutch dust, I could have eaten off of it!

That's where my concern arises. I'll drive the car less than 2k a year. I'm thinking that I should let that sleeping dog lie. I'm concerned that I'm more likely to cause a leak than to prevent one. Any thoughts?

CdnRD is offline   Reply With Quote
Old 01-01-2017, 07:46 AM   #2
Registered User
 
Dave S.'s Avatar
 
Join Date: Oct 2008
Location: Colorado
Posts: 317
When I had my IMSB done by a shop I had them also replace the RMS and the clutch while they were in there. The car only had 25k miles on it and neither the RMS or clutch had any issue, but I thought, while it was all torn apart, why not freshen up the area so it would all be set for 50k miles before needing service again. My plan is to have it all replaced again at 75k miles when the ceramic IMS bearing needs to be replaced. Hopefully, the other parts will last that long and it will all be on the same schedule for maintenance in the future.
__________________
Dave S.
2003 Boxster S
Dave S. is offline   Reply With Quote
Old 01-01-2017, 08:04 AM   #3
Registered User
 
Join Date: May 2014
Location: S.California
Posts: 2,027
The best tech info on this subject is on Renntech by JFP. Elsewhere there is lots of well intentioned noise. Ahsai posted some excellent photos that confirm the advice and experience of JFP.
The very short incomplete version is:
1.to be successful, RMS replacement requires scrupulous attention to tedious.obscure details -per most M96 issues!
2.use the 997 upgraded part
3.use the correct tool -diy construction O.K.
4.set to the correct depth & slightly deeper than any groove worn in the c/s.
The "slap it in & get 'er done guys" need not apply. Better to leave the old one in place for them.
Gelbster is offline   Reply With Quote
Old 01-01-2017, 09:12 AM   #4
Certified Boxster Addict
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 7,669
The justification for replacing the RMS is that the rubber is now 15 years old and has probably lost much of its elasticity making it a prime suspect for a possible leak in the future.

But as you mention, any type of invasive procedure creates the risk of introducing or creating a problem where there was none previously.

If it were me, I'd replace it while following Gelbster's advice regarding JFP's recommended best practices.
__________________
1999 996 C2 - sold - bought back - sold for more
1997 Spec Boxster BSR #254
1979 911 SC
POC Licensed DE/TT Instructor
thstone is offline   Reply With Quote
Old 01-01-2017, 09:32 AM   #5
Registered User
 
Join Date: Jan 2014
Location: New Jersey
Posts: 1,631
FWIW, I had my IMSB replaced at 42k miles on my '03S in 2012. The RMS was bone dry, and consulting with my Indie P car specialist doing the work we decided to leave it alone. At 48k miles the RMS started leaking, so the transmission came back out and I got a new RMS. I am now at 65k miles and it is still dry. I don't know if removing and replacing the flywheel puts any new forces on the end of the crank or the RMS which could cause it to start leaking, but mine did start to leak 6,000 miles and a year after the IMSB was replaced. In the future, like when I need a new clutch, and if I replace the IMSB again, I may just do the RMS again too.
PaulE is offline   Reply With Quote
Old 01-01-2017, 09:48 AM   #6
Registered User
 
jaykay's Avatar
 
Join Date: Sep 2009
Location: toronto
Posts: 2,668
Even though my newly installed 997 seal blew out during a track day I would still go ahead and change it as advised herein
__________________
986 00S
jaykay is offline   Reply With Quote
Old 01-01-2017, 10:30 AM   #7
Registered User
 
Join Date: Aug 2015
Location: Brandon MB
Posts: 51
I'm a careful guy when I do this kind of work but I'm not so confident about my skills. I've done an RMS in the past but not on a Porsche and the "floating" seal that isn't seated against anything makes me nervous. Great advice here though. I'll try to make a tool and if that works out, I'll do the job.
CdnRD is offline   Reply With Quote
Old 01-01-2017, 11:12 AM   #8
Registered User
 
Join Date: May 2014
Location: S.California
Posts: 2,027
The newest seals are much more durable than the old ones.They are however, very tedious to fit correctly.

Last edited by Gelbster; 01-01-2017 at 11:36 AM. Reason: corrected
Gelbster is offline   Reply With Quote
Old 01-01-2017, 11:31 AM   #9
Registered User
 
Join Date: Feb 2005
Location: It's a kind of magic.....
Posts: 6,261
Quote:
Originally Posted by Gelbster View Post
The newest seals are polyurethane which is much more durable than the old ones.They are however, very tedious to fit correctly.
Actually, the updated RMS seals are a PTFE material which was designed to correct the problems encountered with the original Viton seals.

I would not hesitate to replace your original Viton seal with the PTFE unit; they are inexpensive and do an excellent job. As mentioned, all surfaces must be scrupulously cleaned and you should not touch any of the new RMS surfaces without wearing latex or nitrile gloves as even finger prints can cause leaks. Do not use any type of sealant and be sure it is installed straight and to the correct depth.
__________________
Anything really new is invented only in one’s youth. Later, one becomes more experienced, more famous – and more stupid.” - Albert Einstein
JFP in PA is offline   Reply With Quote
Old 01-01-2017, 01:22 PM   #10
Registered User
 
Join Date: Aug 2015
Location: Brandon MB
Posts: 51
Thank you for the advice. I'll keep things clean and if I mess the seal up putting it in I can always get another.

CdnRD is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 05:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page