Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster Racing Forum

Post Reply
 
LinkBack Thread Tools Display Modes
Old 03-05-2012, 08:35 PM   #1
Registered User
 
ChrisZang's Avatar
 
Join Date: Mar 2006
Location: San Carlos, CA 94070
Posts: 1,450
OK, thanks to the hints of other posters I figured it out:
I don't remember if it was JFP or jaykay but someone said that there is another opening for a sensor on the other side of the engine and after initially looking at the wrong place I finally found it

On the first picture I point to the location of the opening (this picture was taken after I already had installed the oil temp sensor). It sits way below the fuel rail (much deeper than it looks on the picture) and is also hidden behind several electrical lines (and yes I have to clean my engine):



Basically look for an oil drain plug on top of the engine (I forgot to take a picture while the plug was still installed, but this is how it looks):



The bore is the same as for the oil pressure probe: M14x1.5

Closer shot of the installed sensor, in the upper left is the air filter and the lower left the MAF:




So I ordered from Pelican: 323-055-M82 (temp sender, I would advise against a sensor which intrudes deeper into the engine) and 310-012-M82 (VDO Gauge).

I spare you the detailled description how to route a cable from the engine to the dashboard (basically I zip tied the cable to the tube between the airbox and the throttle body and after that to the big cable which goes through the rubber grommet in the firewall, from there under the center console and voila)

I compared the readings on the VDO gauge vs. the reading on the Durametric and the readings are spot on within +/- 2% of the readings from the Durametric

Enjoy
__________________
I still wave at Boxsters, but they no longer wave back :-(
2002 Boxster S "Violet" (sold but not forgotten)
2009 Carrera 4S "Kelsey" (current ride)
2015 FIAT 500e "Nikki" my commuter car

Last edited by ChrisZang; 04-14-2012 at 07:08 AM.
ChrisZang is offline   Reply With Quote
Old 03-06-2012, 09:00 AM   #2
Registered User
 
Join Date: Sep 2011
Location: Reno, NV
Posts: 148
Gauges

Where did you mount your gauges? I did the same thing with mine, and put the gauges down low, front of the shifter.
onaFLYer is offline   Reply With Quote
Old 03-06-2012, 11:06 AM   #3
Registered User
 
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,984
Great post

I would like to know if you can swap one of the earlier dash instruments that include an oil pressure gauge for one in the Cayman

.
Gilles is online now   Reply With Quote
Old 03-06-2012, 07:29 PM   #4
Registered User
 
ChrisZang's Avatar
 
Join Date: Mar 2006
Location: San Carlos, CA 94070
Posts: 1,450
Quote:
Originally Posted by Gilles View Post
I would like to know if you can swap one of the earlier dash instruments that include an oil pressure gauge for one in the Cayman

.
So what you mean is installing a 996 cluster in a 987 - no way
Not sure if anyone ever tried to install a 997 cluster in a 987.

Installing a 996 cluster in a 986 is pretty much straightforward:
http://www.pelicanparts.com/techarticles/Boxster_Tech/90-ELEC-996_Cluster/90-ELEC-996_Cluster.htm
__________________
I still wave at Boxsters, but they no longer wave back :-(
2002 Boxster S "Violet" (sold but not forgotten)
2009 Carrera 4S "Kelsey" (current ride)
2015 FIAT 500e "Nikki" my commuter car
ChrisZang is offline   Reply With Quote
Old 03-07-2012, 06:59 AM   #5
Registered User
 
jaykay's Avatar
 
Join Date: Sep 2009
Location: toronto
Posts: 2,668
Chris!

Glad you got it and found the left bank plug. What t fitting did you use to double up the idiot light sender and oil pressure transducer? Oh yeah you are 996 clustered; there may may be no need with the 996 transducer...
__________________
986 00S
jaykay is offline   Reply With Quote
Old 07-02-2012, 11:12 PM   #6
Registered User
 
The Radium King's Avatar
 
Join Date: Apr 2010
Location: Canada
Posts: 3,152
hi folks, a bit of a resurrection here. i like the VDO temp sensor solution and am going to use it. thinking of an autometer dual gauge pod and putting a VDO oil pressure gauge in the other spot. i have two questions:

1) there are two ranges available, 80 and 150 psi; i presume 80 psi max is the best (the oem gauge goes to 5 bar or 72 psi).

2) pressure sender. folks use the 996 pressure sender when doing the 996 cluster conversion, and i've read that the output of this sender is approximately equal to the VDO 10 ohm to 180 ohm requirements. can anyone confirm this? otherwise, the VDO sender looks to have the same thread as the 996 unit and comes with an idiot light on/off switch, so i should be able to use it in place of the 996 unit (it is also cheaper); can onyone confirm this?

thanks, trk.
The Radium King is online now   Reply With Quote
Old 07-03-2012, 12:34 AM   #7
Registered User
 
Join Date: Jul 2012
Posts: 3
Pretty interesting sensor then.
jennilynB is offline   Reply With Quote
Old 07-06-2012, 07:26 AM   #8
Registered User
 
ChrisZang's Avatar
 
Join Date: Mar 2006
Location: San Carlos, CA 94070
Posts: 1,450
Quote:
Originally Posted by The Radium King View Post
1) there are two ranges available, 80 and 150 psi; i presume 80 psi max is the best (the oem gauge goes to 5 bar or 72 psi).

Yes, I'd go with 80 psi

2) pressure sender. folks use the 996 pressure sender when doing the 996 cluster conversion, and i've read that the output of this sender is approximately equal to the VDO 10 ohm to 180 ohm requirements. can anyone confirm this? otherwise, the VDO sender looks to have the same thread as the 996 unit and comes with an idiot light on/off switch, so i should be able to use it in place of the 996 unit (it is also cheaper); can onyone confirm this?



thanks, trk.
As far as I know the thread is M14x1.5
__________________
I still wave at Boxsters, but they no longer wave back :-(
2002 Boxster S "Violet" (sold but not forgotten)
2009 Carrera 4S "Kelsey" (current ride)
2015 FIAT 500e "Nikki" my commuter car
ChrisZang is offline   Reply With Quote
Old 03-06-2012, 01:41 PM   #9
Registered User
 
ChrisZang's Avatar
 
Join Date: Mar 2006
Location: San Carlos, CA 94070
Posts: 1,450
Quote:
Originally Posted by onaFLYer View Post
Where did you mount your gauges? I did the same thing with mine, and put the gauges down low, front of the shifter.
Haven't decided yet if I mount the permanently or only for track days, but probably in the center console.
Looks like Pedro's Technolab has some nice gauges and gauge holders.

What I really would like to do is to convert the voltmeter in my 996 cluster into an oil temp gauge (yet another project ...)
__________________
I still wave at Boxsters, but they no longer wave back :-(
2002 Boxster S "Violet" (sold but not forgotten)
2009 Carrera 4S "Kelsey" (current ride)
2015 FIAT 500e "Nikki" my commuter car
ChrisZang is offline   Reply With Quote
Old 03-06-2012, 07:14 PM   #10
Registered User
 
ChrisZang's Avatar
 
Join Date: Mar 2006
Location: San Carlos, CA 94070
Posts: 1,450
someone sent me a PM asking how I installed the oil pressure sender and I accidentally deleted his message, so here is the response:

It's pretty much all described here:
Pelican Technical Article: Boxster 996 Gauge Cluster Upgrade - 986 Boxster (1997-04) -

Simply "fast forward" to the chapter "installation"
__________________
I still wave at Boxsters, but they no longer wave back :-(
2002 Boxster S "Violet" (sold but not forgotten)
2009 Carrera 4S "Kelsey" (current ride)
2015 FIAT 500e "Nikki" my commuter car
ChrisZang is offline   Reply With Quote
Old 08-16-2018, 07:04 PM   #11
Registered User
 
Join Date: Jan 2017
Location: Miami, FL
Posts: 266
Quote:
Originally Posted by ChrisZang View Post
OK, thanks to the hints of other posters I figured it out:
I don't remember if it was JFP or jaykay but someone said that there is another opening for a sensor on the other side of the engine and after initially looking at the wrong place I finally found it

On the first picture I point to the location of the opening (this picture was taken after I already had installed the oil temp sensor). It sits way below the fuel rail (much deeper than it looks on the picture) and is also hidden behind several electrical lines (and yes I have to clean my engine):



Basically look for an oil drain plug on top of the engine (I forgot to take a picture while the plug was still installed, but this is how it looks):



The bore is the same as for the oil pressure probe: M14x1.5

Closer shot of the installed sensor, in the upper left is the air filter and the lower left the MAF:




So I ordered from Pelican: 323-055-M82 (temp sender, I would advise against a sensor which intrudes deeper into the engine) and 310-012-M82 (VDO Gauge).

I spare you the detailled description how to route a cable from the engine to the dashboard (basically I zip tied the cable to the tube between the airbox and the throttle body and after that to the big cable which goes through the rubber grommet in the firewall, from there under the center console and voila)

I compared the readings on the VDO gauge vs. the reading on the Durametric and the readings are spot on within +/- 2% of the readings from the Durametric

Enjoy
Sorry for the 6-year bump but you just might have made my day. I only need to know a couple of things:

1. Is this port located in the same spot on a 996 3.4 engine (that's what my '99 Boxster has)?

2. Is this the same port that the DOF feeds from (I have Pedro's DOF but can't remember what port it plugs into)?

Of course I could open the lid of my Boxster and look but right now it's nowhere near me

Thanks all
Javi Cooper is offline   Reply With Quote
Old 10-15-2024, 05:38 AM   #12
Registered User
 
Join Date: Feb 2022
Location: Mi
Posts: 7
I know this is an old thread.... But do you have any info on how to wire the sender to the gauge? I'm a newbie on wiring but want to install what you have outlined.

So I ordered from Pelican: 323-055-M82 (temp sender, I would advise against a sensor which intrudes deeper into the engine) and 310-012-M82 (VDO Gauge).

I spare you the detailled description how to route a cable from the engine to the dashboard (basically I zip tied the cable to the tube between the airbox and the throttle body and after that to the big cable which goes through the rubber grommet in the firewall, from there under the center console and voila)

I compared the readings on the VDO gauge vs. the reading on the Durametric and the readings are spot on within +/- 2% of the readings from the Durametric

Enjoy[/QUOTE]
bbmidmi is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 07:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page