Looking for advice

[Mark_T]

OK. Let's all re-type everything that's ever been said in this forum because this guy doesn't wanna use the search button.

[DFromC]

Originally Posted by Mark_T

OK. Let's all re-type everything that's ever been said in this forum because this guy doesn't wanna use the search button.

I searched a ton. A lot of good info. No need to get testy.

[Steve Tinker]

Originally Posted by DFromC

I searched a ton. A lot of good info. No need to get testy.

If you "searched a ton" why did you ask the question?
Honestly, there are dozens of the same inquiries as you are making regarding the pitfalls of owning a M96 engined Boxster. Did you read mikesporscheboxsterwebpages or pedrosgarages.com-Site-Technolab.html

Preferring an S over a base is purely subjective and there is no right or wrong answer....

[DFromC]

Originally Posted by Steve Tinker

If you "searched a ton" why did you ask the question?
Honestly, there are dozens of the same inquiries as you are making regarding the pitfalls of owning a M96 engined Boxster. Did you read mikesporscheboxsterwebpages or pedrosgarages.com-Site-Technolab.html

Preferring an S over a base is purely subjective and there is no right or wrong answer....

No, I didn't see those.. I'll look now.

I asked because as these vehicles age, their issues will become more prevalent. An issue ten years ago may not be an issue today, if say, it can be assumed most cars of this vintage have had the IMS and RMS replaced with a clutch maintenance.

Getting the most up to date info from the experts seemed like a prudent approach.

I realize that repetitive questions can get old, but there are a lot of threads, and a lot of information. Apologies for rehashing it.

[Tcar]

Originally Posted by DFromC

... if say, it can be assumed most cars of this vintage have had the IMS and RMS replaced with a clutch maintenance...

No, you can't assume that. Most cars have NOT had the IMS bearing replaced.

I've even seen a number that had the clutch replaced but not the IMS. Even single row cars (like the one I bought.)

I like the extra torque that the 'S' has.
The 6 speed is a non-issue for me (assume it's mostly for better gas mileage).

The base is still pretty peppy and they both handle very, very well.

[Jamesp]

Underpowered, yet slow, the base continues to fill a much needed void.

Ok - I just posted that to see if there was anyone who would rise to the bait!

[78F350]

Originally Posted by DFromC

I searched a ton. A lot of good info. No need to get testy.

If I understand Canadian customs correctly, Mark_T has offended you and is now obligated to take you out to Timmy's and make reparations. Have him let you drive his car.

Other than the IMS, are there other things I should be looking for over and above basic cosmetic appearance?

Like any 10+ year old used car, some are good, some are bad. If you are not familiar with them, hire a professional to do a pre-purchase inspection.

I generally buy them wrecked or highly depreciated at my own risk. I enjoy doing most of my own work, short of machine shop stuff. Competent shops that work on these cars charge a bit over $100/hour for labor and will not discount your parts. That makes a big difference in whether a problem is cheap or expensive to fix.

Very common problems:
-Missing/broken plastic panels on the undercarriage.
-Malfunctioning windows.
-Airbag system failure (most commonly seat belt wiring).
-Horn contact failure.
-Water pump failure.
-Coolant expansion tank (or cap) leak.
-Brake wear.
-Uneven tire wear.
-Worn suspension parts - rear trailing arms especially.
-Broken parts in the top mechanism - gears, cables, and linkage.
-Blocked drains. Leads to: Wet padding under carpet, failed immobilizer box, corrosion inside brake booster, and more.
-S models commonly have a problem with 2nd gear pop-out
-Spark plug tubes leak. (1997-2002)
-Alternator bearings/idler pulleys seize.
-The Air Oil Separators fail internally and dump oil directly into the intake.

Those are just some of the most common, easy to fix things that I have found on my cars. There's plenty more scary stuff that is less common:
-Failed hydraulic lifters.
-Bad chain tensioners.
-Sheared crankshaft.
-Oil pump failures.
-VarioCam actuator failure.
-Connecting rod bolt failure.
-Rear main seal failure.
Most of these can lead to a repair cost of thousands of dollars (or Very Many thousands of Canadian dollars).

My advice: Buy one that looks pretty and drive it hard. Consider your money gone. For me, it somehow worked out better than my investment in the Oil and Gas industry.

[DFromC]

You understand Canadian customs very well... but it would be rude of me to point out that I'd been offended

He can take me in his Porsche - I'll reciprocate and take him out in my NAS Land Rover Defender 90. Or the Range Rover.. either way, it's a different kind of fun.

Appreciate all the recommendations to do a PPI - None of the local dealers want to do one, so I'm going to contact the local PCA chapter (yes, there's a few Canadian Chapters!) and start asking a lot of questions.

The only dealer that was interested in doing something like a PPI was offering a 110-point inspection, plus a 4-5 hour compression and leak-down test @ $159/hour... and I thought Land Rover dealerships had expensive shop rates! LOL

I also have a sailboat, so I'm familiar with shredding hundred dollar bills and getting wet...

Originally Posted by 78F350

If I understand Canadian customs correctly, Mark_T has offended you and is now obligated to take you out to Timmy's and make reparations. Have him let you drive his car.



Like any 10+ year old used car, some are good, some are bad. If you are not familiar with them, hire a professional to do a pre-purchase inspection.

I generally buy them wrecked or highly depreciated at my own risk. I enjoy doing most of my own work, short of machine shop stuff. Competent shops that work on these cars charge a bit over $100/hour for labor and will not discount your parts. That makes a big difference in whether a problem is cheap or expensive to fix.

Very common problems:
-Missing/broken plastic panels on the undercarriage.
-Malfunctioning windows.
-Airbag system failure (most commonly seat belt wiring).
-Horn contact failure.
-Water pump failure.
-Coolant expansion tank (or cap) leak.
-Brake wear.
-Uneven tire wear.
-Worn suspension parts - rear trailing arms especially.
-Broken parts in the top mechanism - gears, cables, and linkage.
-Blocked drains. Leads to: Wet padding under carpet, failed immobilizer box, corrosion inside brake booster, and more.
-S models commonly have a problem with 2nd gear pop-out
-Spark plug tubes leak. (1997-2002)
-Alternator bearings/idler pulleys seize.
-The Air Oil Separators fail internally and dump oil directly into the intake.

Those are just some of the most common, easy to fix things that I have found on my cars. There's plenty more scary stuff that is less common:
-Failed hydraulic lifters.
-Bad chain tensioners.
-Sheared crankshaft.
-Oil pump failures.
-VarioCam actuator failure.
-Connecting rod bolt failure.
-Rear main seal failure.
Most of these can lead to a repair cost of thousands of dollars (or Very Many thousands of Canadian dollars).

My advice: Buy one that looks pretty and drive it hard. Consider your money gone. For me, it somehow worked out better than my investment in the Oil and Gas industry.

[husker boxster]

Originally Posted by DFromC

None of the local dealers want to do one, so I'm going to contact the local PCA chapter (yes, there's a few Canadian Chapters!) and start asking a lot of questions.

The only dealer that was interested in doing something like a PPI was offering a 110-point inspection, plus a 4-5 hour compression and leak-down test @ $159/hour... and I thought Land Rover dealerships had expensive shop rates! LOL

Sadly, fewer places are doing PPIs because they don't want the liability of something breaking 1 mo later and the customer coming back to them to pay for it. Good things always go bad when lawyers get involved.

And welcome to the world of expensive German cars, but you should be aware of this world if you have an Audi.

Good luck with your search. You are heading into a good time to buy with fall approaching. Any dealer in your area with a Boxster should be willing to deal on it. They don't want to go deep into Sep with a convertible sports car on their lot.

[DFromC]

I do all my own wrench work on the Audi, unless it's electronic...

Originally Posted by husker boxster

Sadly, fewer places are doing PPIs because they don't want the liability of something breaking 1 mo later and the customer coming back to them to pay for it. Good things always go bad when lawyers get involved.

And welcome to the world of expensive German cars, but you should be aware of this world if you have an Audi.

Good luck with your search. You are heading into a good time to buy with fall approaching. Any dealer in your area with a Boxster should be willing to deal on it. They don't want to go deep into Sep with a convertible sports car on their lot.

[DFromC]

Originally Posted by DFromC

I do all my own wrench work on the Audi, unless it's electronic...

Just did both rear hub and bearings - you do NOT want to know what the torque setting is for those axle bolts... think as high as you reasonably think a bolt goes on, then add something insane, and you're getting close...

[DFromC]

As a side-note, I have a highly modified 362HP 2007 Audi A3 going up for sale that will fund the purchase of the 986... APR tune, S3 intercooler, K04 Stage 2 Turbo, APR downpipe, carbonio intake, APR HPFP, Bosch Hi-Flow injectors, poly dog bone bushing, BSH engine mount, BSH PCV revamp, etc, etc.. list goes on for a while..

Originally Posted by 78F350

If I understand Canadian customs correctly, Mark_T has offended you and is now obligated to take you out to Timmy's and make reparations. Have him let you drive his car.



Like any 10+ year old used car, some are good, some are bad. If you are not familiar with them, hire a professional to do a pre-purchase inspection.

I generally buy them wrecked or highly depreciated at my own risk. I enjoy doing most of my own work, short of machine shop stuff. Competent shops that work on these cars charge a bit over $100/hour for labor and will not discount your parts. That makes a big difference in whether a problem is cheap or expensive to fix.

Very common problems:
-Missing/broken plastic panels on the undercarriage.
-Malfunctioning windows.
-Airbag system failure (most commonly seat belt wiring).
-Horn contact failure.
-Water pump failure.
-Coolant expansion tank (or cap) leak.
-Brake wear.
-Uneven tire wear.
-Worn suspension parts - rear trailing arms especially.
-Broken parts in the top mechanism - gears, cables, and linkage.
-Blocked drains. Leads to: Wet padding under carpet, failed immobilizer box, corrosion inside brake booster, and more.
-S models commonly have a problem with 2nd gear pop-out
-Spark plug tubes leak. (1997-2002)
-Alternator bearings/idler pulleys seize.
-The Air Oil Separators fail internally and dump oil directly into the intake.

Those are just some of the most common, easy to fix things that I have found on my cars. There's plenty more scary stuff that is less common:
-Failed hydraulic lifters.
-Bad chain tensioners.
-Sheared crankshaft.
-Oil pump failures.
-VarioCam actuator failure.
-Connecting rod bolt failure.
-Rear main seal failure.
Most of these can lead to a repair cost of thousands of dollars (or Very Many thousands of Canadian dollars).

My advice: Buy one that looks pretty and drive it hard. Consider your money gone. For me, it somehow worked out better than my investment in the Oil and Gas industry.