Changing the coolant breather valve - 986 Forum - The Community for Porsche Boxster & Cayman Owners

shlim8 · 03-08-2011, 03:51 AM

Sigh, the new breather valve did not solve the problem.... or maybe I've got a new problem, don't really know as I never knew where the "old" leakage was...

I've now got bubbling from the bottom of the breather valve housing, when the car is hot and left idling for a while.

My first thought was that the 0 rings were not seated properly. I've re-installed the breather valve 3 times, checked for dirt, cracks or anything that might cause a leak. Can't see anything and the bubbling is always at the same exact spot !

The threads of the bolts holes in the coolant tank seems fine, but is it possble that the leakage is from one of the bolt holes ?? Bubbling is from the side of one of the hole locations. I'm pretty sure the O ring is seated properly. The bolts are tighten to hand tight and then about 1/8 of a turn more or less. The bolts were really loose on the original breather valve.

Any ideas ?? Other than a new coolant tank ??

insite · 03-08-2011, 04:36 AM

you have a crack. time for a new tank.

Dale_K · 03-08-2011, 06:17 AM

Anybody have a picture of the tank opening once the bleeder valve is removed? I replaced my bleeder last week and didn't see any o-rings at all. There was a circular disc with a couple rows of holes sort of near the center but I didn't lift that off. Are the o-rings under that? I doubt my bleeder valve was actually bad. The new and old looked and operated identically.

Andrew McD · 03-08-2011, 02:01 PM

Is it possible to remove the valve to see if it needs replacing? And if so what would I be looking for?

Thanks, A.

schoir · 03-08-2011, 05:28 PM

Quote:

Originally Posted by Andrew McD

Is it possible to remove the valve to see if it needs replacing? And if so what would I be looking for?

Thanks, A.

Andrew:

Yes, it can be removed... See the photo I attached in the previous post for what you end up with once it's completely removed.

If you go to the trouble of removing it, you may as well replace the O-rings.

Also inspect the rubber membrane immediately under the top portion of the assembly.

There is a photo of a defective one earlier in this thread.

BE VERY SURE to heed the cautions against overtorquing the bolts.

Regards, Maurice.

shlim8 · 03-08-2011, 05:38 PM

Quote:

Originally Posted by Andrew McD

Is it possible to remove the valve to see if it needs replacing? And if so what would I be looking for?

Thanks, A.

It is possible to remove the valve, but I wouldn't mess around with the valve unless u intend to change it or the O rings. The design of where the bolts go into the coolant tank is downright scary. There are just holes on the top of the coolant tank, not raised or marked so it's easy to mis-thread them. And this is 10 yr old plastic (in my case).

There is only 2 things you can change - the entire valve (which includes the valve, housing, 2 O rings and the bolts in one set) or the 2 O rings (can be bought separately).

Dale_K · 03-09-2011, 03:48 AM

Thanks for that picture. I ordered the bleeder valve and O-rings from an online parts house and then before the order arrived I got an email with a $5 credit, which kind of confused me. When the shipment arrived there were no O-rings with the bleeder. Instead there was a brake pad sensor, lol. I guess the guys got it wrong when they packed the order and then noticed the extra O-rings laying around and figured out what happened and gave me the credit. I can get O-rings from the hardware store now that your picture shows me where they're supposed to go.

insite · 03-09-2011, 04:08 AM

Dale -

FYI, it's not an o-ring, it's a square ring. there is a difference, and an o-ring probably won't work here. be sure you pick up a compatible seal. see the photo in post #10 above.

Quote:

Originally Posted by Dale_K

Thanks for that picture. I ordered the bleeder valve and O-rings from an online parts house and then before the order arrived I got an email with a $5 credit, which kind of confused me. When the shipment arrived there were no O-rings with the bleeder. Instead there was a brake pad sensor, lol. I guess the guys got it wrong when they packed the order and then noticed the extra O-rings laying around and figured out what happened and gave me the credit. I can get O-rings from the hardware store now that your picture shows me where they're supposed to go.

shlim8 · 03-08-2011, 05:13 PM

Quote:

Originally Posted by Dale_K

Anybody have a picture of the tank opening once the bleeder valve is removed? I replaced my bleeder last week and didn't see any o-rings at all. There was a circular disc with a couple rows of holes sort of near the center but I didn't lift that off. Are the o-rings under that? I doubt my bleeder valve was actually bad. The new and old looked and operated identically.

The O rings are below the breather valve housing (the one with a couple row of holes).

My new and old valve were NOT the exactly the same.... It looked the same but after installing it, I realized that the valve (centre plastic piece with the metal ring) was sticking out alittle higher. I thought I messed up somewhere so I removed it - and noticed that the rubber diaphram was alittle thicker. Hence, the valve sticks out more after installing.

It was the second install that did me in.... It was perfectly dry after the initial install. I started getting bubbling from the housing after the 2nd install. Sigh... should have left it. I think my expansion tank just went south.

schoir · 03-08-2011, 05:25 PM

Quote:

Originally Posted by Dale_K

Anybody have a picture of the tank opening once the bleeder valve is removed? I replaced my bleeder last week and didn't see any o-rings at all. There was a circular disc with a couple rows of holes sort of near the center but I didn't lift that off. Are the o-rings under that? I doubt my bleeder valve was actually bad. The new and old looked and operated identically.

Dale:

Top of coolant tank with bleeder valve assembly removed:

Regards, Maurice.

insite · 03-09-2011, 04:10 AM

slim -

in maurice's photo above, from where is your new leak bubbling?

shlim8 · 03-09-2011, 05:34 PM

Hi insure, the bubbling is from an area below the valve housing, close to one of the bolt holes. After careful inspection, there are 3 small and light "scratches" there. Turns out they are prob hairline cracks. Very hard to see and bubbles only when the water temp goes beyond 80 degrees C. The tank is toast, got that changed yesterday. Guess it's better to discover the prob now when I'm monitoring the breather valve than the tank letting go in the middle of the highway.

Btw my Porsche original O rings are really round not square.

insite · 03-10-2011, 03:02 AM

sorry to hear your tank is dead. thx for the info that your kit came w/ an o-ring & not a square ring. looks like the factory thinks either solution is ok here. take care.