Dual DIN 7" Touch screen radio install

[BestGear]

Originally Posted by Sanford_yee

I'm interested to know how does the audio for the phone sound like for both caller and receiver? Also, when you get done, can you tell us how you connected the wiring (color to color). I hate figuring out where the wiring goes and too lazy to search.

Thanks!

Audio quality on my kenwwod is good too - I used the dash lockation for the microphone - just mounted the kenwod mike behind the porsche bezel.

The wiring on mine was std ISO, with the exception of the reverse wire (for camera) and handbrake (to prevent viewing of movies while in motion) - of course you can just earth that wire.

Other than that, its phonos for the amp if you have one.


David

[jb92563]

Originally Posted by BestGear

The wiring on mine was std ISO, with the exception of the reverse wire (for camera) and handbrake (to prevent viewing of movies while in motion)
David

What wire did you use for the reverse sensing so that the rear camera comes on automatically?

[BestGear]

Originally Posted by jb92563

What wire did you use for the reverse sensing so that the rear camera comes on automatically?

I fitted rear parking sensors at the same time the bumper was off - a well spent £15 for them - supplied painted a very close colour match too! I just ran a wire from the rear boot - but the reverse signal is available from the ECU under the (UK) passenger seat.

On my kenwood you can set it up to auto switch over to the reverse camera or ignore it.

Also, you can select the camera while traveling forward too should you wish.


See the camera and parking installs below..









David

[SoK]

soooo it sounds like wiring should be plug and play (for speakers) with this unit, is that right?

I'll mess with the backup camera when the car's apart, doesn't sound too bad to do once we're able to easily ID (hopefully with pics) something to wire it into for reverse.

So at this point, finding a cage for this $200 unit is the hangup..

[BestGear]

Originally Posted by SoK

So at this point, finding a cage for this $200 unit is the hangup..

Here is the Connects2 cage/facia I used - I expect it will be around in the US too somewhere.

I dont endorse this seller, its only FYI

Facia

[jb92563]

Hmmmm, don't really want to mess with the ECU for a reverse signal since a mistake there could be quite expensive.

If that reverse wire on the Radio is simply a ground signal then a simple little microswitch will work for that attached to the shifter mechanics.

I have a short shifter to install anyways so if the microswitch idea is viable then it will be time for the short shifter install as well.

"Change one thing....change everything!" rings true again.

[BestGear]

Originally Posted by jb92563

If that reverse wire on the Radio is simply a ground signal then a simple little microswitch will work for that attached to the shifter mechanics.

The handbrake wire needs grounded to activate (ie, brake on), the reverse wire needs 12V + on it to activate (ie, go into reverse).

David

[jb92563]

Here is the face plate I cut out of some 1/8" thick aluminum. The side wings will be bolted to the radio and then the whole thing as a unit fits into the opening.
There is a lip at the bottom that the bottom part keys into and the top will be secured by two screws into the existing two plastic screw holes.



Here it is in the dash before the plastic trim that came with the radio.
A plastic surround will be cut to fit around the radio on top of the aluminum to finish the plastic work.



Here is the radio with the included plastic trim. Still need to select and cut the plastic surround that goes on top of the aluminum. All that shows is a bit at the top and a very little bit at the bottom.

[jb92563]

Originally Posted by SoK

soooo it sounds like wiring should be plug and play (for speakers) with this unit, is that right?

I'll mess with the backup camera when the car's apart, doesn't sound too bad to do once we're able to easily ID (hopefully with pics) something to wire it into for reverse.

So at this point, finding a cage for this $200 unit is the hangup..

Yes, Plug and play for the speakers, power, Illumination(headlights on signal)

Power + (Yellow),Ground - (Black) , Illumination (Orange), Switched + (Red)


You cut midway through the middle mounting hole and tray seperator. Don't need to cut the top one.


8.5" (216mm) deep slot for the double DIN radio.


The included plastic faceplate(Not shown) will cover the entire width but the part above needs a cover. More on that to come.


The Yellow connector has the speakers on it if you have a factory Amp, but there is a Brown connector instead (Not in this pic) if you dont have an Amp, with your speaker connections.