Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 08-11-2020, 03:05 PM   #1
Registered User
 
Join Date: May 2018
Location: Michigan
Posts: 104
Drop Link bolt stuck and I'm out of ideas

Rear drop link on passenger side. The smooth bolt through the wheel carrier is beyond stuck. I removed the socket from the ball side and I can get an impact on the nut type section below the ball. The bolt will turn with an impact wrench on it. It will not budge to move out. I've tried heat, cans of liquid wrench, wd 40, hammer, bigger hammer, biggerer hammer, tried getting a gear puller on it.

No joy. I am completely out of luck ....... it's now day 4......

2ata is offline   Reply With Quote
Old 08-11-2020, 03:26 PM   #2
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
It looks like this is not uncommon, although I haven't tried on mine. You said it turns with an impact? Does the bolt spin with the nut? If so you may have to cut it off on the nut side or try to get a wrench or visegrips on the other side to hold it.

Someone else had a similar issue, but he was able to get the nut off, the bolt was stuck:
http://986forum.com/forums/boxster-general-discussions/47796-rear-drop-links-help.html
__________________
2002 Boxster Base - Arctic Silver - Tiptronic
2010 Subaru Forester
1980 Ford C-8000 Custom Cab Emergency-One Fire Truck
__________________
"I never lose. I either win or I learn." -Nelson Mandela

Last edited by piper6909; 08-11-2020 at 03:36 PM.
piper6909 is offline   Reply With Quote
Old 08-11-2020, 03:46 PM   #3
Registered User
 
Join Date: May 2018
Location: Michigan
Posts: 104
Nut came off from the thread end with no issue. It's literally the smooth bolt through the wheel carrier where it is stuck. I previously confirmed that the entire bolt turns with the impact wrench.
2ata is offline   Reply With Quote
Old 08-11-2020, 04:13 PM   #4
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
Quote:
Originally Posted by 2ata View Post
Nut came off from the thread end with no issue. It's literally the smooth bolt through the wheel carrier where it is stuck. I previously confirmed that the entire bolt turns with the impact wrench.
See if one of there will fit over it:
https://www.harborfreight.com/3-4-quarter-inch-forged-ball-joint-separator-99849.html

If the bolt turns, all you should need some pressure to push it out while you hit it with the impact. The problem you're having now is that while the impact turns it, there's no pressure to pull it out. Actually the impact is probably applying force that keeps it in. You need pressure from the other side to push it out. Maybe this tool will help. It may even push it out without the impact.
__________________
2002 Boxster Base - Arctic Silver - Tiptronic
2010 Subaru Forester
1980 Ford C-8000 Custom Cab Emergency-One Fire Truck
__________________
"I never lose. I either win or I learn." -Nelson Mandela

Last edited by piper6909; 08-11-2020 at 04:19 PM.
piper6909 is offline   Reply With Quote
Old 08-11-2020, 05:23 PM   #5
Registered User
 
Qingdao's Avatar
 
Join Date: Jul 2019
Location: Charleston
Posts: 509
Cut off wheel.
__________________
'99 supercharged 4.3 chevy Boxsterado
'98 PP13B powered thing

WTB: any cheap 986 shifter new or used
Qingdao is offline   Reply With Quote
Old 08-11-2020, 05:45 PM   #6
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
Quote:
Originally Posted by Qingdao View Post
Cut off wheel.
That would help if the nut is stuck on the bolt and the bolt free-spins in the housing. He has the opposite problem. The nut is off. The bolt is stuck in the housing. He'll need to push the bolt out while turning it with the impact.
__________________
2002 Boxster Base - Arctic Silver - Tiptronic
2010 Subaru Forester
1980 Ford C-8000 Custom Cab Emergency-One Fire Truck
__________________
"I never lose. I either win or I learn." -Nelson Mandela
piper6909 is offline   Reply With Quote
Old 08-11-2020, 06:12 PM   #7
Registered User
 
Qingdao's Avatar
 
Join Date: Jul 2019
Location: Charleston
Posts: 509
Ah, I see he can't get the bolt that affixes the link to the strut/spindle.


Use a ball joint press or a c-clamp. Put a socket on the one side to give an area of recess and a punch on the other end to drive it through.

Air hammer helps.
__________________
'99 supercharged 4.3 chevy Boxsterado
'98 PP13B powered thing

WTB: any cheap 986 shifter new or used
Qingdao is offline   Reply With Quote
Old 08-11-2020, 06:19 PM   #8
Will there be cake?
 
tonythetiger's Avatar
 
Join Date: Mar 2017
Location: East Coast
Posts: 623
Garage
I had one stuck once and used my torch, red hot then cooled with ice, two cycles. Came right out when I twisted with a wrench.


Sent from my iPhone using Tapatalk
tonythetiger is offline   Reply With Quote
Old 08-11-2020, 06:25 PM   #9
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
Quote:
Originally Posted by Qingdao View Post
Ah, I see he can't get the bolt that affixes the link to the strut/spindle.


Use a ball joint press or a c-clamp. Put a socket on the one side to give an area of recess and a punch on the other end to drive it through.

Air hammer helps.
I suggested the ball joint press, but I like the C-clamp and socket idea better!
__________________
2002 Boxster Base - Arctic Silver - Tiptronic
2010 Subaru Forester
1980 Ford C-8000 Custom Cab Emergency-One Fire Truck
__________________
"I never lose. I either win or I learn." -Nelson Mandela
piper6909 is offline   Reply With Quote
Old 08-11-2020, 06:34 PM   #10
Registered User
 
Qingdao's Avatar
 
Join Date: Jul 2019
Location: Charleston
Posts: 509
Quote:
Originally Posted by piper6909 View Post
See if one of there will fit over it:
https://www.harborfreight.com/3-4-quarter-inch-forged-ball-joint-separator-99849.html

If the bolt turns, all you should need some pressure to push it out while you hit it with the impact. The problem you're having now is that while the impact turns it, there's no pressure to pull it out. Actually the impact is probably applying force that keeps it in. You need pressure from the other side to push it out. Maybe this tool will help. It may even push it out without the impact.
Sorry... I miss links sometimes.


If the OP loosens the toe control arm link (??? Correct term??) and the CV axle he'll be able to twist the strut. That'll give him a better angle on the bolt so he can strike it; like hitting a home run.
__________________
'99 supercharged 4.3 chevy Boxsterado
'98 PP13B powered thing

WTB: any cheap 986 shifter new or used
Qingdao is offline   Reply With Quote
Old 08-11-2020, 08:24 PM   #11
Registered User
 
Join Date: Jan 2020
Location: Boston
Posts: 78
Lots of PB Blaster, and get it spinning with the impact gun. Spray again, and spin opposite direction. Once you spin it a few times in both directions, the corrosion should loosen up and you can back it out........ both of my rear shocks had this problem...... 20 years in New England.....

-Eric
Eric-986 is offline   Reply With Quote
Old 08-12-2020, 03:05 AM   #12
Registered User
 
Join Date: May 2018
Location: Michigan
Posts: 104
I'll have to try the C clamp this evening.


Heat, cool, and lube were all a no go in any combination. Impact wrench and a Hulk smash BFH when applied together offered nothing.
2ata is offline   Reply With Quote
Old 08-12-2020, 09:24 AM   #13
Registered User
 
morgal48's Avatar
 
Join Date: Jan 2014
Location: Texas
Posts: 221
If I understand your issue, have you jacked the wheel carrier up, or let it down, at the LCA ball joint to change the angle? It could be bound up (binded?) due to the non alignment of the holes at the other end where the offending bolt is. The bolt could spin, but not release.
__________________
2000 Boxster S
2010 Volvo XC60
2011 GMC Denali HD 6.6L (sold)
2008 Cayenne S (sold)
1989 Targa (sold)
morgal48 is offline   Reply With Quote
Old 08-12-2020, 10:02 AM   #14
Registered User
 
Join Date: Jan 2020
Location: Boston
Posts: 78


The corrosion builds up on the middle of the bolt, keeping it from sliding out...... I had the best luck with the impact gun spinning the bolt to "grind" off the corrosion.... it did take a little while though.

-Eric

99 986
09 Cayman S
Eric-986 is offline   Reply With Quote
Old 08-12-2020, 10:05 AM   #15
Registered User
 
Join Date: May 2018
Location: Michigan
Posts: 104
Quote:
Originally Posted by morgal48 View Post
If I understand your issue, have you jacked the wheel carrier up, or let it down, at the LCA ball joint to change the angle? It could be bound up (binded?) due to the non alignment of the holes at the other end where the offending bolt is. The bolt could spin, but not release.
Yes I have tried jacking it up, down, every which way without any advantage.
2ata is offline   Reply With Quote
Old 08-12-2020, 02:59 PM   #16
Registered User
 
Join Date: Aug 2018
Location: Woodland Wa
Posts: 1,291
Get some ATF and some Acetone.
Mix 50/50.
shake the hell out of it. (each time you use it) and saturate the bolt as often as you can over a 24 hour period.
get a muffler gun. (Air operated impact gun) fitted with a punch.

Cheap at Harbor freight.

You should have very little problem driving it out with a muffler gun.
Especially since you can turn it.


Last edited by blue62; 08-12-2020 at 03:02 PM.
blue62 is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 12:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page