Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Show and Tell Gallery

Post Reply
 
LinkBack Thread Tools Display Modes
Old 07-03-2007, 01:16 PM   #1
ddb
www.klisstle.com
 
ddb's Avatar
 
Join Date: Sep 2004
Location: Charlotte, NC
Posts: 926
Garage
Thanks guys.

I had read about how difficult it would be to drill through the brake pedal, so I was prepared. My cordless drill isn't that powerful, so I didn't even try to use it. I just broke out my seldom used old electric drill. On top of that, I bought a new set of drill bits. I then took advice I read here or on another site and started with a very small pilot hole, and enlarged the hole with different drill bits until reaching the desired diameter. Lastly, I removed the plastic owner's manual holder under the steering wheel in order to get a better angle with my drill. After taking these steps, it was rather easy to drill the holes. I made marks on my rubber brake and clutch covers and drilled through rubber before going through the substrate. I believe the rubber acted as a guide and prevented the drill bit from sliding around on the metal or plastic.

I hope these tips will be helpful to the next guy.

ddb

Edit - I forgot to say that I didn't use the rubber brake and clutch covers in the final install. I used them as guides and removed them before attaching the metal covers.

Last edited by ddb; 07-03-2007 at 01:47 PM.
ddb is offline   Reply With Quote
Old 07-03-2007, 02:28 PM   #2
Registered User
 
Join Date: Oct 2005
Location: canada
Posts: 42
Do you mind me asking where you got them and how much they cost?
porscheman is offline   Reply With Quote
Old 07-03-2007, 03:47 PM   #3
ddb
www.klisstle.com
 
ddb's Avatar
 
Join Date: Sep 2004
Location: Charlotte, NC
Posts: 926
Garage
No problem. I bought them on eBay for $69.99. Shipping was rather high at $25.00. The seller's name is orangehuang531.

ddb
ddb is offline   Reply With Quote
Old 07-07-2007, 03:28 PM   #4
Registered User
 
Join Date: Jun 2006
Location: Idaho
Posts: 5
gas pedal question

i poped my gas pedal off and now I can't get the ball back in the cup on the back of the gas pedal, do you know how to get it reconnected/
gpminow is offline   Reply With Quote
Old 07-07-2007, 04:41 PM   #5
ddb
www.klisstle.com
 
ddb's Avatar
 
Join Date: Sep 2004
Location: Charlotte, NC
Posts: 926
Garage
Sorry gpminow, no experience reconnecting the gas pedal. I'm sure someone with knowledge will chime in.

Good luck, and post some pics when you're done.
ddb is offline   Reply With Quote
Old 07-07-2007, 07:46 PM   #6
Registered User
 
Join Date: Mar 2007
Location: New Jersey
Posts: 89
Send a message via AIM to [z0ne] Send a message via MSN to [z0ne]
Very nice, ddb. The new pedals are a much-needed improvement over the stock ones. If you don't mind me asking, how much did you pay for the set? I assume the set of three came with the dead pedal, too?
[z0ne] is offline   Reply With Quote
Old 07-07-2007, 09:16 PM   #7
Registered User
 
Join Date: Sep 2005
Location: Sacramento
Posts: 3,417
Send a message via AIM to blinkwatt
Very nice!
__________________
-99' Zenith Blue 5-spd...didn't agree with a center divider on the freeway
-01' S Orient Red Metallic 6-spd...money pit...sold to buy a house
blinkwatt is offline   Reply With Quote
Old 07-07-2007, 09:20 PM   #8
Registered User
 
Join Date: Sep 2006
Location: California
Posts: 713
Quote:
Originally Posted by [z0ne]
Very nice, ddb. The new pedals are a much-needed improvement over the stock ones. If you don't mind me asking, how much did you pay for the set? I assume the set of three came with the dead pedal, too?

Here ya go:

Quote:
Originally Posted by [ddb]
No problem. I bought them on eBay for $69.99. Shipping was rather high at $25.00. The seller's name is orangehuang531.

ddb
__________________
http://farm4.static.flickr.com/3420/...90927559_o.jpg

Some stuff for sale: M030 S 24mm front sway bar, M030 base 19.6mm rear sway bar, 996 GT3 OEM Porsche Motorsport front strut mounts monoball "camber plates"

WTB: looking for some 5-7mm spacers with extended bolts
chaudanova is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 08:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page