Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Performance and Technical Chat

Post Reply
 
LinkBack Thread Tools Display Modes
Old 01-21-2024, 04:24 PM   #1
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Diagnostic help needed! Hot film MAF and low oxygen adaptation.

I need some diagnostic help on my 2001 Boxster S. I recently performed some maintenance and a few test drives later got some error codes

Maintenance:

- New spark plugs, tubes/o-rings, and coil packs. Test drive was fine no misfires, etc. I burned off some on of the engine cleaner that dripped on the cats, but no issues. (Note: old tubes were leaking, old spark plugs were for a 2.5l not a 3.2l, all old coil packs were fine, but I replaced them anyway).

- Gear oil change - drilled the aluminum pan to access the drain plug. Drained/filled no issue once the plugs finally let loose.

- New fuel filter - replaced the fuel filter with no issue. Started fine after a couple cranks to refill the fuel lines, no leaks, smells, hesitation, etc.

- New engine mount - replaced the worn engine mount with the new 987 style mount. Had a little trouble lowering and raising the engine. I put the jack behind the oil pan toward the transmission near the cable that ties the engine to the chassis. this caused the engine to tilt a little more forward when lowering and made raising it harder. It lowered 3-4 inches and when I raised it back up I squished out some of the fluid in the passenger side transmission mount. I was mad mad mad at myself for not just placing the jack on the oil pan instead. Anyway, car started up fine and ran smoother than ever.

Issue:

Car was riunning better then every, then on the third or fourth test drive, I was cruising down the highway at about 80-85 mph. I had some right front wheel vibration that I still haven't sorted out yet. Pretty sure the tire is out of balance. Anyway, during that period of vibration, the check engine light beeped and may have flashed. So i pull off the highway and looked over the car. No leaks, smoke, rough idle, noises, etc. So I drove it home slowly hoping it was just a hiccup in the system after all the changes.

The next morning on a cold start the car ran a little rough and made a little rattling on the driver side near the catalytic converter. Sounded like a screw rattling. But it went away after the SAI kicked off (i think). It doesn't rattle everytime, but something is off and its idling just a tad rough.

I got an ODBII code reader and this is what popped up.
P0102 - Hot film MAF Sensor
P1126 - Oxygen sensing adaptation, lower load range, bank 1
P1133 - Oxygen sensing adaptation, lower load range, bank 2

Thoughts:

I thought maybe I knocked something loose when I lowered and raised the engine. So I "popped" the hood and started looking around, but nothing seems disconnected on the intake or the SAI. The oil filler tube also seems fine, no big oil leaks or anything. When driving the car in and out of the garage with the engine cover off I can hear a pressure release sound when I give it gas under load. Not sure if that's normal.

I could try a new MAF sensor, but I find it hard to believe the MAF went out right during my test drive window. Is there something obvious I should be checking? I was expecting to find some kind of intake leak or blockage.

Thank you for making through my wall of text!

__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-21-2024, 07:10 PM   #2
Registered User
 
Join Date: Feb 2005
Location: It's a kind of magic.....
Posts: 6,482
Both the 1126 and 1133 are typically an indication of an intake aire leak.
__________________
Anything really new is invented only in one’s youth. Later, one becomes more experienced, more famous – and more stupid.” - Albert Einstein
JFP in PA is online now   Reply With Quote
Old 01-21-2024, 07:28 PM   #3
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Do you think it’s likely between airbox and throttle body?

Quote:
Originally Posted by JFP in PA View Post
Both the 1126 and 1133 are typically an indication of an intake aire leak.
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-22-2024, 07:35 AM   #4
Registered User
 
Join Date: Feb 2005
Location: It's a kind of magic.....
Posts: 6,482
Quote:
Originally Posted by Danimal View Post
Do you think it’s likely between airbox and throttle body?
Without a smoke test, no way of telling....................
__________________
Anything really new is invented only in one’s youth. Later, one becomes more experienced, more famous – and more stupid.” - Albert Einstein
JFP in PA is online now   Reply With Quote
Old 01-22-2024, 08:51 AM   #5
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
That's what I was afraid of. Here's the plan for now. Please let me know if there is a better way to do.

1. Test MAF values in live data in my code reader (if possible).
2. Clean MAF and reset/retest.
3. Assuming I still have a problem, remove intake tube, cover the throttle body and smoke the rest of the intake system via one of the connections behind the throttle.
4. Fix any leaks and clean throttle body.
5. Pray to the Porsche gods for mercy!

There is a little bit of oily build up at the connection between the oil filler accordion and the part that attaches to the engine. no drips on the engine. Could the be my culprit?

Quote:
Originally Posted by JFP in PA View Post
Without a smoke test, no way of telling....................
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 02:40 PM   #6
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Quick update. I decided to start my pulling and cleaning the throttle body. That way there would be more room to look around for anything obviously wrong.

The throttle body is dirty (64K and probably never cleaned), but pretty clean from behind the valve and through the intake manifold. There is some oil, but I think it is acceptable. The PO said the AOS was replaced at some point. Please let me know if this amount of oil looks troubling or not.

There was also a strong gas smell from inside the intake. You could immediately smell it after removing the throttle body.

That said, there is damp residue all over the lower pivot for the resonance tube valve. I've read this could be power steering overflow and there is a small old gooey puddle of it in one of the crevices on the block. Do you think this valve could be my vacuum leak? Or this is just old power steering fluid?
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"

Last edited by Danimal; 01-23-2024 at 02:51 PM. Reason: added more information
Danimal is online now   Reply With Quote
Old 01-23-2024, 02:43 PM   #7
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Pictures



__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 02:47 PM   #8
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
more pictures






__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 04:22 PM   #9
Registered User
 
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,919
Quote:
Originally Posted by Danimal View Post
Or this is just old power steering fluid?
Have you taste it? (seriously..) as oil and hydraulic fluid taste completely different.. you don't need to drink it, just the tip of your finger will give you an accurate taste..
Gilles is online now   Reply With Quote
Old 01-23-2024, 06:19 PM   #10
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
I dabbed a piece of paper towel in it and smelled it....but it didn't smell like anything....iI guess I should have tasted it!

Quote:
Originally Posted by Gilles View Post
Have you taste it? (seriously..) as oil and hydraulic fluid taste completely different.. you don't need to drink it, just the tip of your finger will give you an accurate taste..
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 06:23 PM   #11
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Here's a shot of the resonance flap hinge.

__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 07:33 PM   #12
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
The check valve going into the resonance tube boot is oily on the boot side. The PCV valve is also very wet/oily.

To replace to replace the check valve, is it just press fit?
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-23-2024, 10:02 PM   #13
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Here are pictures of the PCV and check valve.




__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-24-2024, 06:48 PM   #14
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Do you think I should be concerned about the gas smell in the intake? Could it be a bad regeneration valve for the evap?
Quote:
Originally Posted by JFP in PA View Post
Without a smoke test, no way of telling....................
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-25-2024, 05:19 AM   #15
Registered User
 
Join Date: Aug 2018
Location: Woodland Wa
Posts: 1,300
Quote:
Originally Posted by Danimal View Post
Do you think I should be concerned about the gas smell in the intake? Could it be a bad regeneration valve for the evap?
I would worry about the oily residue and oil saturated dirt all over the engine.
It is definitive proof of multiple vacuum leaks.
blue62 is online now   Reply With Quote
Old 01-25-2024, 10:45 AM   #16
Registered User
 
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,919
Quote:
Originally Posted by blue62 View Post
I would worry about the oily residue and oil saturated dirt all over the engine.
It is definitive proof of multiple vacuum leaks.
+1 Yes! The first step would be to clean your engine then start troubleshooting
Gilles is online now   Reply With Quote
Old 01-25-2024, 03:12 PM   #17
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Thanks, I’ve been cleaning as I go by hand. I really want to spray this thing down and start fresh, but now is not the time for that. And for the record I didn’t let it get this way, but it’s on me for buying such a dirty car.

I just cleaned the MAF sensor and sucked a few small pieces of leaves off the air straightener. No oil in the intake tube, but a little dusty. MAF wasn’t too bad.

I just ordered a smoke machine. I guess we’ll see what we find.

Quote:
Originally Posted by Gilles View Post
+1 Yes! The first step would be to clean your engine then start troubleshooting
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-25-2024, 03:30 PM   #18
Registered User
 
Join Date: Aug 2018
Location: Woodland Wa
Posts: 1,300
Quote:
Originally Posted by Danimal View Post
Thanks, I’ve been cleaning as I go by hand. I really want to spray this thing down and start fresh, but now is not the time for that. And for the record I didn’t let it get this way, but it’s on me for buying such a dirty car.

I just cleaned the MAF sensor and sucked a few small pieces of leaves off the air straightener. No oil in the intake tube, but a little dusty. MAF wasn’t too bad.

I just ordered a smoke machine. I guess we’ll see what we find.
You may want to look at the condition of your air filter while your in there.
blue62 is online now   Reply With Quote
Old 01-25-2024, 04:12 PM   #19
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
Fortunately, the air filter is new and there were only a couple very small leaves in the bottom of the box.

Quote:
Originally Posted by blue62 View Post
You may want to look at the condition of your air filter while your in there.
__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Old 01-27-2024, 10:30 AM   #20
Registered User
 
Join Date: May 2023
Location: Oakland, CA
Posts: 198
I spent the last week mapping out each of the vacuum systems and AOS tubes and I think I finally understand what everything is. Smoke machine has arrived and smoke will be commencing in T minus 1hr.

__________________
2001 Boxster S | Triple Black | Stock 17s | Bilstein PSS9s | BAD Shifter | 6x40w Cabrio Amp | 986.2 muffler

"Sixty percent of the time, it works every time!"
Danimal is online now   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 06:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page