Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Performance and Technical Chat

Post Reply
 
LinkBack Thread Tools Display Modes
Old 12-16-2014, 12:53 PM   #1
Registered User
 
Join Date: Jun 2012
Location: Frederick MD
Posts: 658
Oil type and timing chain rattle on start-up

Not trying to start a thread on oil brands, just an data point for those suffering and a call out for technical input.

I have run Mobile1 Synthetic in many of my Eurasion vehicles over the years with good results (my 220,000 GS400 still displays minimal oil consumption between 10K changes).

I am too swamped for a DIY at the moment, so I had my local shop change my oil recently. They filled my 2002 S (81,000) with Motul synthetic 5W-40 instead of M1 synthetic 0W-40 I've used at home.

When I picked up the car, there was zero rattle on start-up. Engine was cold, so I assumed someone had recently moved the car outside and that the tensioners were still full of oil. The next morning when I started the engine The lack of noise got my attention. There was a barely audible difference in mechanical noise for the first .10th of a second, but not really what could be considered a rattle. The car is no longer "embarrassing" to cold start up in front of people.

Can any one explain why heavier weight oil would pressurize the tensioners faster than lighter weight oil...especially on sub freezing mornings?

I'm baffled by this.

shadrach74 is offline   Reply With Quote
Old 12-16-2014, 01:26 PM   #2
Registered User
 
The Radium King's Avatar
 
Join Date: Apr 2010
Location: Canada
Posts: 3,121
higher cold weight means less drain-down and ensures that a light film of oil remains on the chains/pads for start-up. i only run 5w40 and, with the oil piston update, no longer have start-up rattle.
The Radium King is offline   Reply With Quote
Old 12-16-2014, 01:57 PM   #3
Registered User
 
Join Date: Feb 2005
Location: It's a kind of magic.....
Posts: 6,261
Quote:
Originally Posted by shadrach74 View Post
Not trying to start a thread on oil brands, just an data point for those suffering and a call out for technical input.

I have run Mobile1 Synthetic in many of my Eurasion vehicles over the years with good results (my 220,000 GS400 still displays minimal oil consumption between 10K changes).

I am too swamped for a DIY at the moment, so I had my local shop change my oil recently. They filled my 2002 S (81,000) with Motul synthetic 5W-40 instead of M1 synthetic 0W-40 I've used at home.

When I picked up the car, there was zero rattle on start-up. Engine was cold, so I assumed someone had recently moved the car outside and that the tensioners were still full of oil. The next morning when I started the engine The lack of noise got my attention. There was a barely audible difference in mechanical noise for the first .10th of a second, but not really what could be considered a rattle. The car is no longer "embarrassing" to cold start up in front of people.

Can any one explain why heavier weight oil would pressurize the tensioners faster than lighter weight oil...especially on sub freezing mornings?

I'm baffled by this.

Higher base weight oils typically demonstrate higher film strength than their lower base weight analogs. This increase in film strength results in slower drain down over time and that gives better parts coating at start up. What you are seeing is the most commonly observed result.
__________________
Anything really new is invented only in one’s youth. Later, one becomes more experienced, more famous – and more stupid.” - Albert Einstein
JFP in PA is offline   Reply With Quote
Old 12-16-2014, 02:14 PM   #4
still plays with cars...
 
BoxsterSteve's Avatar
 
Join Date: May 2011
Location: Baden, ON, Canada
Posts: 1,087
Garage
Quote:
Originally Posted by The Radium King View Post
higher cold weight means less drain-down and ensures that a light film of oil remains on the chains/pads for start-up. i only run 5w40 and, with the oil piston update, no longer have start-up rattle.
Hey King,
What is this oil piston update you speak of?
__________________
Six speed 2000 Boxster S
Arctic Silver on Metropol Blue | LN Dual Row IMSR | Arctic Silver console, spoiler frame & bumperettes | Crios mod | Technobrace | RoboTop module & modified convertible top relay for one-touch roof operation
BoxsterSteve is offline   Reply With Quote
Old 12-16-2014, 02:19 PM   #5
Registered User
 
Join Date: May 2011
Location: Miami florida
Posts: 1,591
I've tried everything from 0- 40 to 20-50 oil in my car and the startup rattle does not go away. I've also replaced the lower two tensioners with no change. one of these days I may replace the upper tensioner but for the moment I just live with the start up rattle.
__________________
Current car

2000 Boxster 2.7l red/black

Previous cars

1973 Opel Manta
1969(?) Fiat 850 Convertible
1979 Lancia Beta Coupe
1981 Alfa Romeo GTV 6
1985 Alfa Romeo Graduate
1985 Porsche 944
1989 Porsche 944
1981 Triumph TR7
1989 (?) Alfa Romeo Milano
1993 Saab 9000
san rensho is offline   Reply With Quote
Old 12-16-2014, 03:10 PM   #6
Registered User
 
The Radium King's Avatar
 
Join Date: Apr 2010
Location: Canada
Posts: 3,121
part # 26 in the attached link:

Oil Pump

note that it is a 997 part number. it is beveled where the original was square. my understanding (worth what you pay for it on the internet) is that the original was binding, and the role of the piston is to increase oil pressure at start-up. a 5-minute job at your next oil change.

it's an interesting exercise to go through the parts catalog and look for superseded part numbers and 997 part numbers - aos for example ...
The Radium King is offline   Reply With Quote
Old 12-16-2014, 03:40 PM   #7
still plays with cars...
 
BoxsterSteve's Avatar
 
Join Date: May 2011
Location: Baden, ON, Canada
Posts: 1,087
Garage
Thanks! I've got some rattle, maybe this will help.
__________________
Six speed 2000 Boxster S
Arctic Silver on Metropol Blue | LN Dual Row IMSR | Arctic Silver console, spoiler frame & bumperettes | Crios mod | Technobrace | RoboTop module & modified convertible top relay for one-touch roof operation
BoxsterSteve is offline   Reply With Quote
Old 12-16-2014, 04:50 PM   #8
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Quote:
Originally Posted by The Radium King View Post
part # 26 in the attached link:

Oil Pump

note that it is a 997 part number. it is beveled where the original was square. my understanding (worth what you pay for it on the internet) is that the original was binding, and the role of the piston is to increase oil pressure at start-up. a 5-minute job at your next oil change.

it's an interesting exercise to go through the parts catalog and look for superseded part numbers and 997 part numbers - aos for example ...
I did this two oil changes ago and it was very easy to do and only a few $$$.
steved0x is offline   Reply With Quote
Old 12-16-2014, 06:09 PM   #9
Registered User
 
kjc2050's Avatar
 
Join Date: Oct 2012
Location: Wake Forest, NC
Posts: 867
Garage
Quote:
Originally Posted by steved0x View Post
I did this two oil changes ago and it was very easy to do and only a few $$$.
Is this readily accessible from the bottom of the engine?
__________________
2000 Boxster S, 6 speed, Sport Package, Litronics, LED tail lights, LNE IMS-B, OBC, Skybreaker wind deflector, Arctic Silver/Graphite Grey
kjc2050 is offline   Reply With Quote
Old 12-16-2014, 07:00 PM   #10
Registered User
 
Join Date: May 2011
Location: Miami florida
Posts: 1,591
Quote:
Originally Posted by The Radium King View Post
part # 26 in the attached link:

Oil Pump

note that it is a 997 part number. it is beveled where the original was square. my understanding (worth what you pay for it on the internet) is that the original was binding, and the role of the piston is to increase oil pressure at start-up. a 5-minute job at your next oil change.

it's an interesting exercise to go through the parts catalog and look for superseded part numbers and 997 part numbers - aos for example ...
Did that, no change in the start up rattle, but definitely something you should do.
__________________
Current car

2000 Boxster 2.7l red/black

Previous cars

1973 Opel Manta
1969(?) Fiat 850 Convertible
1979 Lancia Beta Coupe
1981 Alfa Romeo GTV 6
1985 Alfa Romeo Graduate
1985 Porsche 944
1989 Porsche 944
1981 Triumph TR7
1989 (?) Alfa Romeo Milano
1993 Saab 9000
san rensho is offline   Reply With Quote
Old 12-17-2014, 08:46 AM   #11
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Quote:
Originally Posted by kjc2050 View Post
Is this readily accessible from the bottom of the engine?
It is, I don't think I had to remove any panels or anything to get to it, I think it was right in front of the sump cover.

I think it was parts 5, 25, and 26 that I replaced from this diagram.

http://www.********************************************.com/porsche-parts/hardparts.php?dir=986-97-04&section=104-00

It was easily accessible from the bottom. And now maybe I am remembering that I did need to remove the rearmost plastic underbody tray... It has been a while

Tightening torque for the bolt (part 4 in the diagram) is 25NM/18FT/LB.

Last edited by steved0x; 12-17-2014 at 08:54 AM.
steved0x is offline   Reply With Quote
Old 12-17-2014, 11:14 AM   #12
Registered User
 
kjc2050's Avatar
 
Join Date: Oct 2012
Location: Wake Forest, NC
Posts: 867
Garage
Quote:
Originally Posted by steved0x View Post
It is, I don't think I had to remove any panels or anything to get to it, I think it was right in front of the sump cover.

I think it was parts 5, 25, and 26 that I replaced from this diagram.

Oil Pump

It was easily accessible from the bottom. And now maybe I am remembering that I did need to remove the rearmost plastic underbody tray... It has been a while

Tightening torque for the bolt (part 4 in the diagram) is 25NM/18FT/LB.
Thanks! Appreciate the info.
__________________
2000 Boxster S, 6 speed, Sport Package, Litronics, LED tail lights, LNE IMS-B, OBC, Skybreaker wind deflector, Arctic Silver/Graphite Grey
kjc2050 is offline   Reply With Quote
Old 12-17-2014, 01:47 PM   #13
Beginner
 
Jamesp's Avatar
 
Join Date: Mar 2013
Location: Houston
Posts: 1,659
Garage
Quote:
Originally Posted by san rensho View Post
I've tried everything from 0- 40 to 20-50 oil in my car and the startup rattle does not go away. I've also replaced the lower two tensioners with no change. one of these days I may replace the upper tensioner but for the moment I just live with the start up rattle.
You might ask Jake if he will part with a couple of his master link chains so you can cut yours out and replace them with new without the inconvenience of removing and completely disassembling the engine. It may be stretched (read that worn) chains contributing as much or more to the rattle than weak tensioners.
__________________
2003 S manual
Jamesp is offline   Reply With Quote
Old 12-17-2014, 02:18 PM   #14
Registered User
 
jaykay's Avatar
 
Join Date: Sep 2009
Location: toronto
Posts: 2,668
Quote:
Originally Posted by Jamesp View Post
You might ask Jake if he will part with a couple of his master link chains so you can cut yours out and replace them with new without the inconvenience of removing and completely disassembling the engine. It may be stretched (read that worn) chains contributing as much or more to the rattle than weak tensioners.
Wow I would like to know how this is accomplished with the engine in the car!
__________________
986 00S
jaykay is offline   Reply With Quote
Old 12-17-2014, 06:32 PM   #15
Engine Surgeon
 
Join Date: Aug 2008
Location: Cleveland GA USA
Posts: 2,425
Oil does impact tensioner rattle.. This is in part to the way oils will retain pressure in their tensors, as well as how well the boundary layer protection is able to buffer the sound of the chains.

Oils high in Moly love tensioners. The best oil to quieten tensioners has always been redline. Our latest generation of DT40 is the best its ever been for this, as well.
__________________
Jake Raby/www.flat6innovations.com
IMS Solution/ Faultless Tool Inventor
US Patent 8,992,089 &
US Patent 9,416,697
Developer of The IMS Retrofit Procedure- M96/ M97 Specialist
Jake Raby is offline   Reply With Quote
Old 12-17-2014, 06:58 PM   #16
Registered User
 
Join Date: May 2011
Location: Miami florida
Posts: 1,591
Quote:
Originally Posted by Jake Raby View Post
Oil does impact tensioner rattle.. This is in part to the way oils will retain pressure in their tensors, as well as how well the boundary layer protection is able to buffer the sound of the chains.

Oils high in Moly love tensioners. The best oil to quieten tensioners has always been redline. Our latest generation of DT40 is the best its ever been for this, as well.
I tried Redline and as the french say, no diffrance.
__________________
Current car

2000 Boxster 2.7l red/black

Previous cars

1973 Opel Manta
1969(?) Fiat 850 Convertible
1979 Lancia Beta Coupe
1981 Alfa Romeo GTV 6
1985 Alfa Romeo Graduate
1985 Porsche 944
1989 Porsche 944
1981 Triumph TR7
1989 (?) Alfa Romeo Milano
1993 Saab 9000
san rensho is offline   Reply With Quote
Old 12-17-2014, 07:13 PM   #17
Registered User
 
Join Date: May 2011
Location: Miami florida
Posts: 1,591
Quote:
Originally Posted by Jamesp View Post
You might ask Jake if he will part with a couple of his master link chains so you can cut yours out and replace them with new without the inconvenience of removing and completely disassembling the engine. It may be stretched (read that worn) chains contributing as much or more to the rattle than weak tensioners.
Wow. Thanks for tHe tip, but I have to say Im not that ambitious. Many many of 986 and 996 motors rattle on startup but apparently there is no correlation between start up rattle and engine failure. Its one of the quirks of the brand, like when I had Alfa Romeos, the synchros were horrible, but you learned how to double clutch and they drove wonderfully.
__________________
Current car

2000 Boxster 2.7l red/black

Previous cars

1973 Opel Manta
1969(?) Fiat 850 Convertible
1979 Lancia Beta Coupe
1981 Alfa Romeo GTV 6
1985 Alfa Romeo Graduate
1985 Porsche 944
1989 Porsche 944
1981 Triumph TR7
1989 (?) Alfa Romeo Milano
1993 Saab 9000
san rensho is offline   Reply With Quote
Old 12-17-2014, 07:44 PM   #18
Engine Surgeon
 
Join Date: Aug 2008
Location: Cleveland GA USA
Posts: 2,425
Quote:
Originally Posted by san rensho View Post
I tried Redline and as the french say, no diffrance.
Then you have a tensioner issue, or chain issue, or both. The IMS tensioner is the worst for this, and as it rattles it hammers on the IMS bearing, and it's tensioner paddle and wear pad. I think this contributes at least some to IMSB failure.

Its not a normal occurrence; just because most do it, doesn't make it mechanically acceptable. The tensioners for 5 chain engines have been revised 7 times, 3 chain have been revised 3 times.

If its rattling at start up, things are wearing. Period.

A huge amount of preventative packages we are doing these days end up getting chains, as most are stretched and send the tensioners out of range.
__________________
Jake Raby/www.flat6innovations.com
IMS Solution/ Faultless Tool Inventor
US Patent 8,992,089 &
US Patent 9,416,697
Developer of The IMS Retrofit Procedure- M96/ M97 Specialist
Jake Raby is offline   Reply With Quote
Old 12-18-2014, 05:25 AM   #19
Registered User
 
Join Date: Jul 2009
Location: Arlington Heights, IL
Posts: 1,561
Quote:
Originally Posted by Jake Raby View Post
Our latest generation of DT40 is the best its ever been for this, as well.
Thanks, Jake. I always knew this was coming, but never knew the exact timing. When I asked about this in December/January, last year, the timing was not known, and you had a good inventory of the first gen DT40. When did the update take place? Is there a way to know if the new formula is in the bottle by looking at a specific code or something? Thanks again.
Flavor 987S is offline   Reply With Quote
Old 12-18-2014, 10:09 AM   #20
Engine Surgeon
 
Join Date: Aug 2008
Location: Cleveland GA USA
Posts: 2,425
Quote:
Originally Posted by Flavor 987S View Post
Thanks, Jake. I always knew this was coming, but never knew the exact timing. When I asked about this in December/January, last year, the timing was not known, and you had a good inventory of the first gen DT40. When did the update take place? Is there a way to know if the new formula is in the bottle by looking at a specific code or something? Thanks again.
DT40 has been a continual development since it's conception as "JD Raby's Snake Oil".

The product changed last year, as you are referring to. The new batch is fully developed and is just awaiting blending, and bottling. This newer version improves MPG, helps with tensioner quietness and has proven to pick up a few more ponies in the top end.

__________________
Jake Raby/www.flat6innovations.com
IMS Solution/ Faultless Tool Inventor
US Patent 8,992,089 &
US Patent 9,416,697
Developer of The IMS Retrofit Procedure- M96/ M97 Specialist
Jake Raby is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 05:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page