Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > DIY Project Guides

Post Reply
 
LinkBack Thread Tools Display Modes
Old 01-23-2015, 11:15 AM   #321
Registered User
 
Fintro11's Avatar
 
Join Date: Jun 2013
Location: Nanaimo, Vancouver Island, British Columbia, Canada
Posts: 900
I think it's a security thing going on with the states, some of our work shipments have been sitting at customs for a few days as well

Fintro11 is offline   Reply With Quote
Old 01-23-2015, 10:21 PM   #322
Registered User
 
Nine8Six's Avatar
 
Join Date: Sep 2013
Location: Montreal, QC. (currently expat to Shanghai)
Posts: 3,249
Confirmed working: Ashtray Light connectivity

I can dbl-confirm that Martin's ashtray install methods works just perfectly. The circuit is indeed 6.6volts however it delivers 9V when the SkyBreaker is connected. More than enough current flows to power ON the kit. Looks good!

1) Remove ashtray
2) Unscrew the two torx screws
3) Pull out the assembly and set aside (no need to unplug anything, switches etc)
4) Splice both brown & bleu ashtray light wires and terminate as you wish (soldered mines, covered with 2" of electrical tape. Sufficient)

Brown = ground (goes to SkyBreaker black)
Blue = positive (goes to SkyBreaker red)

No need to remove the console, the cabling is so small it's easy to push under with your fingers. My controller is now residing in the armrest compartment same as Martin's initial idea. I've hidden the 385 kilometers of wires under the carpet/driver's side however

In all, the installation takes aprox 20-30min. From sliding out your OEM windows to closing the lid of the armrest compartment! Way too easy and extremely unchallenging (i.e. boring)

The rest really is to snake the little WD cable around the hoop. Copy what I did (see pics below) or if you are braver than me, pull off the trim and tidy everything inside of it. The reason I chosen this method is because it will be easy to remove for cleaning. I don't want to bother removing the trim each time - I'm suspecting brittle clips under there!







On a side note, I couldn't push back my Boxster inside its storage shed so I had no choice but to start it up. Guess what, went for a 2hrs topless drive (warm and bright sunshine here today). Just came back all fixed lollll haven't driven this car for almost 1.5months. What a blast each time
__________________
______________________________
'97 Boxster base model 2.5L, Guards Red/Tan leather, with a new but old Alpine am/fm radio.

Last edited by Nine8Six; 01-23-2015 at 10:24 PM.
Nine8Six is offline   Reply With Quote
Old 01-24-2015, 08:48 AM   #323
Beginner
 
Jamesp's Avatar
 
Join Date: Mar 2013
Location: Houston
Posts: 1,659
Garage
Quote:
Originally Posted by Fintro11 View Post
I think it's a security thing going on with the states, some of our work shipments have been sitting at customs for a few days as well
I'm still in customs as well. Has anyone's shipment cleared customs?
__________________
2003 S manual
Jamesp is offline   Reply With Quote
Old 01-24-2015, 10:20 AM   #324
Registered User
 
Nine8Six's Avatar
 
Join Date: Sep 2013
Location: Montreal, QC. (currently expat to Shanghai)
Posts: 3,249
Quote:
Originally Posted by Jamesp View Post
I'm still in customs as well. Has anyone's shipment cleared customs?
J - CN4, HK1, Canada3 & UK2 cleared only atm

USA SkyBreakerians - Any concerns by PM pleeze (will send an update privately in 48hrs). Keep The Faith loll
__________________
______________________________
'97 Boxster base model 2.5L, Guards Red/Tan leather, with a new but old Alpine am/fm radio.
Nine8Six is offline   Reply With Quote
Old 01-24-2015, 04:22 PM   #325
Registered User
 
Join Date: Nov 2009
Location: PA
Posts: 170
please let me know when you make more....i'd like to purchase one
geetee is offline   Reply With Quote
Old 01-24-2015, 05:50 PM   #326
Registered User
 
Fintro11's Avatar
 
Join Date: Jun 2013
Location: Nanaimo, Vancouver Island, British Columbia, Canada
Posts: 900



Looks good during the day too
Fintro11 is offline   Reply With Quote
Old 01-24-2015, 06:29 PM   #327
Registered User
 
JonD's Avatar
 
Join Date: Jan 2015
Location: Melbourne, Australia
Posts: 74
[QUOTE=Nine8Six;433070]I can dbl-confirm that Martin's ashtray install methods works just perfectly. The circuit is indeed 6.6volts however it delivers 9V when the SkyBreaker is connected. More than enough current flows to power ON the kit. Looks good!

1) Remove ashtray
2) Unscrew the two torx screws
3) Pull out the assembly and set aside (no need to unplug anything, switches etc)
4) Splice both brown & bleu ashtray light wires and terminate as you wish (soldered mines, covered with 2" of electrical tape. Sufficient)

Brown = ground (goes to SkyBreaker black)
Blue = positive (goes to SkyBreaker red)

No need to remove the console, the cabling is so small it's easy to push under with your fingers. My controller is now residing in the armrest compartment same as Martin's initial idea. I've hidden the 385 kilometers of wires under the carpet/driver's side however
/QUOTE]

Fred,
Sorry to be so pedantic (remember I'm a complete novice)
When you do this:
Splice both brown & bleu ashtray light wires and terminate as you wish
Brown = ground (goes to SkyBreaker black)
Blue = positive (goes to SkyBreaker red)

Does the ashtray light still work after you connect the skybreaker wires? Or does it eliminate the light? Not that it really matters if the light in there is lost, but just wondering.
Plus instead of soldering, I have these wire connectors I use so you don't even have to strip the insulation from the wires and no tape needed.
Sorry if this is a stupid question, I just don't want to short circuit anything
Thank You
__________________
1998 Porsche Boxster
986 Arena Red, Tiptronic Base
JonD is offline   Reply With Quote
Old 01-24-2015, 06:31 PM   #328
Registered User
 
JonD's Avatar
 
Join Date: Jan 2015
Location: Melbourne, Australia
Posts: 74
Quote:
Originally Posted by Fintro11 View Post



Looks good during the day too
Looks great even with the Top up too What's that writing on your mesh deflectors. Are they 3rd party deflectors or just stickers on them?
__________________
1998 Porsche Boxster
986 Arena Red, Tiptronic Base
JonD is offline   Reply With Quote
Old 01-24-2015, 07:30 PM   #329
Registered User
 
Fintro11's Avatar
 
Join Date: Jun 2013
Location: Nanaimo, Vancouver Island, British Columbia, Canada
Posts: 900
Quote:
Originally Posted by JonD View Post
Looks great even with the Top up too What's that writing on your mesh deflectors. Are they 3rd party deflectors or just stickers on them?
club grill badges
Fintro11 is offline   Reply With Quote
Old 01-24-2015, 08:41 PM   #330
Registered User
 
JonD's Avatar
 
Join Date: Jan 2015
Location: Melbourne, Australia
Posts: 74
Quote:
Originally Posted by Fintro11 View Post
club grill badges
They look great, I also noticed from the close up pics you secured the mesh on with a black cable tie. Is one enough?

oooo just noticed too you probably are aware already, with the top up the PORSCHE lettering on the window doesn't centre with the skybreaker PORSCHE lettering. Or maybe it's just the angle the pic was taken
Just saying
Cheers
__________________
1998 Porsche Boxster
986 Arena Red, Tiptronic Base

Last edited by JonD; 01-24-2015 at 09:01 PM.
JonD is offline   Reply With Quote
Old 01-25-2015, 02:29 AM   #331
Registered User
 
mavis.d's Avatar
 
Join Date: Apr 2014
Location: Leeds UK
Posts: 105
It's just the angle, do you really think either Mr F or Dr F would not have got the image central?
mavis.d is offline   Reply With Quote
Old 01-25-2015, 08:17 AM   #332
Registered User
 
Fintro11's Avatar
 
Join Date: Jun 2013
Location: Nanaimo, Vancouver Island, British Columbia, Canada
Posts: 900
[QUOTE=JonD;433162]
Quote:
Originally Posted by Nine8Six View Post
I can dbl-confirm that Martin's ashtray install methods works just perfectly. The circuit is indeed 6.6volts however it delivers 9V when the SkyBreaker is connected. More than enough current flows to power ON the kit. Looks good!

1) Remove ashtray
2) Unscrew the two torx screws
3) Pull out the assembly and set aside (no need to unplug anything, switches etc)
4) Splice both brown & bleu ashtray light wires and terminate as you wish (soldered mines, covered with 2" of electrical tape. Sufficient)

Brown = ground (goes to SkyBreaker black)
Blue = positive (goes to SkyBreaker red)

No need to remove the console, the cabling is so small it's easy to push under with your fingers. My controller is now residing in the armrest compartment same as Martin's initial idea. I've hidden the 385 kilometers of wires under the carpet/driver's side however
/QUOTE]

Fred,
Sorry to be so pedantic (remember I'm a complete novice)
When you do this:
Splice both brown & bleu ashtray light wires and terminate as you wish
Brown = ground (goes to SkyBreaker black)
Blue = positive (goes to SkyBreaker red)

Does the ashtray light still work after you connect the skybreaker wires? Or does it eliminate the light? Not that it really matters if the light in there is lost, but just wondering.
Plus instead of soldering, I have these wire connectors I use so you don't even have to strip the insulation from the wires and no tape needed.
Sorry if this is a stupid questi

on, I just don't want to short circuit anything
Thank You

Ash tray light still works, soldering would be best but connectors will work remember it's very small wire, hard to crimp connectors too.

I will take a picture of it today for you. I had my 8 year old daughter help me hold each wire as I soldiered them
Fintro11 is offline   Reply With Quote
Old 01-26-2015, 05:08 AM   #333
Registered User
 
Join Date: Jun 2014
Location: New Jersey
Posts: 230
Just got this message at 8.00 AM - USPS package Inbound Out of Customs 01/26/2015 4:30am. Your item cleared United States Customs at 4:30 am on January 26, 2015.

Excited!!
__________________
2001 Seal Gray Boxster (Hair Salon on wheels)
2013 Audi Q5 (Family Mover)
2006 Yamaha R1 (Adrenaline Machine)

Last edited by amitmishra4; 01-26-2015 at 05:11 AM.
amitmishra4 is offline   Reply With Quote
Old 01-26-2015, 06:23 AM   #334
Registered User
 
BruceH's Avatar
 
Join Date: Jun 2012
Location: Bedford, TX
Posts: 2,732
Garage
Quote:
Originally Posted by amitmishra4 View Post
Just got this message at 8.00 AM - USPS package Inbound Out of Customs 01/26/2015 4:30am. Your item cleared United States Customs at 4:30 am on January 26, 2015.

Excited!!
Woo Hoo! Mine cleared at 4:23am
__________________
______________________________________________
2001 Boxster S Lapis Blue
TS Cat Bypass Pipes and exhaust
iPad Mini Dash Install
DEPO Tail Lights
BruceH is online now   Reply With Quote
Old 01-26-2015, 06:31 AM   #335
Registered User
 
Join Date: Sep 2013
Location: California
Posts: 466
AS of 630 PST, still stuck in customs in LA. Been sitting there for 5 days now. It took 1 day to get from China to LA, but the efficiency of the the US customs strikes again. Between those jokers and the IRS, well I won't go any further I'm sure NSA is watching.
__________________
"Blind acceptance is a sign, of stupid fools who stand in line."
Slate 01 is offline   Reply With Quote
Old 01-26-2015, 07:20 AM   #336
Registered User
 
ccjazz's Avatar
 
Join Date: May 2012
Location: Vancouver Island, Canada
Posts: 211
Garage
Thanks to everyone who are posting their installations...any other ideas are welcome and I'll be deciding what method suits my limited electrical skills

Tracking shows that my deflector arrived in town over the weekend and should be out for delivery today. Can't wait!

Note to self...remove watches/rings before handling and mild detergent, warm water, clean microfiber when cleaning.
__________________
'01 Boxster S (purchased new) triple black, litronics, cruise, heated seats,18's.
ccjazz is offline   Reply With Quote
Old 01-26-2015, 08:10 AM   #337
Registered User
 
Nine8Six's Avatar
 
Join Date: Sep 2013
Location: Montreal, QC. (currently expat to Shanghai)
Posts: 3,249
Quote:
Originally Posted by ccjazz View Post
Thanks to everyone who are posting their installations...any other ideas are welcome and I'll be deciding what method suits my limited electrical skills
I bet some will come up with pretty fancy set-up - let's see! The easiest = ashtray. I'm also keeping my eyes open for that dual-intensity brake circuit activated thingy. For the red kit I think it would be a nice feature. The other colors aren't much of a 'safety' concern imo, can be turned on anytime/anywhere.

As far as set-up(s) goes, it's all at its infantry atm. Plenty you can do with it

Quote:
Originally Posted by ccjazz View Post
Note to self...remove watches/rings before handling and mild detergent, warm water, clean microfiber when cleaning.
Maintenance is required on this kit. Buy yourself a plastic polishing kit that you can use for headlights, tail lights, and your illuminated WD. One kit fits all (e.g. NOVUS)

And remember, a kit like that is only meant to be effective after you have cleaned & detailed/wax your roadster. Meant to accentuate the topless drive really, stylish!. I leave mine turned off when the roof is up, but turn it ON when the car is spanking clean and roof is down only. Fancy accessories really... looking good is all it does loll

The etch also looks killer in day time. Top quality soft white, frosty, high res, etc. I think you'll all love that effect as well

Exterminate the WD Stickers lolll
__________________
______________________________
'97 Boxster base model 2.5L, Guards Red/Tan leather, with a new but old Alpine am/fm radio.
Nine8Six is offline   Reply With Quote
Old 01-26-2015, 08:19 AM   #338
Registered User
 
Nine8Six's Avatar
 
Join Date: Sep 2013
Location: Montreal, QC. (currently expat to Shanghai)
Posts: 3,249
Quote:
Originally Posted by Slate 01 View Post
AS of 630 PST, still stuck in customs in LA. Been sitting there for 5 days now. It took 1 day to get from China to LA, but the efficiency of the the US customs strikes again. Between those jokers and the IRS, well I won't go any further I'm sure NSA is watching.
Cheap air mail shipping, manual customs clearance, etc etc.... can't be fast mate! When you ask they tell you eta 10-15days (contract promise). And when you complain, they tell you 10-15 "open business days sir" LOL

Its all random really... unreliable timing, etc, but the good part is; it always gets there!

Express shipping however is lighting fast 95% of the time (EMS). At least these guys have clearance broker services at ports of entry. That's embedded in your shipping (fast track). Much faster but sadly twice the price. But hey... 7 days and it's in your hands anywhere in the states (Colorado mountains, bad weather, whatever... "it works")

So much I can help from my end, helpless on that sorry. Fingers crossed guys
__________________
______________________________
'97 Boxster base model 2.5L, Guards Red/Tan leather, with a new but old Alpine am/fm radio.
Nine8Six is offline   Reply With Quote
Old 01-26-2015, 08:31 AM   #339
Registered User
 
hemonu's Avatar
 
Join Date: Oct 2012
Location: Germany
Posts: 43
Garage
Shipment arrived in Germany today Installation will be done next weekend as I have to leave to Paris now ...
__________________
Don't panic !

Last edited by hemonu; 01-26-2015 at 08:57 AM.
hemonu is offline   Reply With Quote
Old 01-26-2015, 08:44 AM   #340
Registered User
 
ccjazz's Avatar
 
Join Date: May 2012
Location: Vancouver Island, Canada
Posts: 211
Garage
Quote:
Originally Posted by Nine8Six View Post
I bet some will come up with pretty fancy set-up - let's see! The easiest = ashtray. I'm also keeping my eyes open for that dual-intensity brake circuit activated thingy. For the red kit I think it would be a nice feature. The other colors aren't much of a 'safety' concern imo, can be turned on anytime/anywhere.

As far as set-up(s) goes, it's all at its infantry atm. Plenty you can do with it



Maintenance is required on this kit. Buy yourself a plastic polishing kit that you can use for headlights, tail lights, and your illuminated WD. One kit fits all (e.g. NOVUS)

And remember, a kit like that is only meant to be effective after you have cleaned & detailed/wax your roadster. Meant to accentuate the topless drive really, stylish!. I leave mine turned off when the roof is up, but turn it ON when the car is spanking clean and roof is down only. Fancy accessories really... looking good is all it does loll

The etch also looks killer in day time. Top quality soft white, frosty, high res, etc. I think you'll all love that effect as well

Exterminate the WD Stickers lolll
I've been using PlastX for the rear window and factory deflector up till now. Seems to work well...is Novus preferable?

__________________
'01 Boxster S (purchased new) triple black, litronics, cruise, heated seats,18's.
ccjazz is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 10:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page