Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 03-08-2007, 09:07 AM   #1
Registered User
 
Join Date: Jul 2006
Location: Where the Sewer Meets the Sea, CA. USA
Posts: 2,695
Send a message via MSN to CJ_Boxster
The screws on the front rotors can be done by hand. The rear rotors will be alittle more stuck, Place a screw driver on then, then give the back of the screwdriver afew good taps on the head with a hammer or heavy wrench... that should make it easier to brake free. You dont need new sensors if you dont have a "Brake Wear" warning light on your dash that is solidly lit while your driving., you can re-use the old ones.
__________________
--Proud Boxster Owner/Tech,

Carlos J Cazares

FastForward Performance
http://i10.photobucket.com/albums/a1...er/newsig1.jpg
CJ_Boxster is offline   Reply With Quote
Old 03-08-2007, 09:24 AM   #2
Registered User
 
Join Date: Sep 2006
Location: new jersey
Posts: 404
the sensors came with the pads so that is why i have new ones. Also, I know you don't use your back but your muscles and nerves run up your back no matter ho you try to avoid it they get used. I have 3 herainted discs in my back from a car accident that is why i asked about the toughness of getting out these screws. My other question is do you tighten the phillips screws by hand or did you use a torque to tighten them. I don't want to be driving down the road and the screws fall out lol.

p.s i am a cert. personal trainer so i know what i am talking about when it comes to the muscle groups and what is used during certain activities
clb0099 is offline   Reply With Quote
Old 03-08-2007, 09:50 AM   #3
Registered User
 
Join Date: Oct 2006
Location: MD
Posts: 447
The proper tool to remove the brake rotor screws is called a hammer driver, or an impact driver (not an impact wrench - this is not an air driven tool, it's a hammer driven tool). Sears sells them. Makes life much, much easier.

Those screws serve no purpose other than to hold the rotors onto the hubs when the car is traveling down the assembly line. You don't even need them. The lug bolts securing the wheel keep the rotor on. No worries about torquing them properly.
John V is offline   Reply With Quote
Old 03-08-2007, 10:01 AM   #4
Registered User
 
Join Date: Dec 2006
Location: Austin, TX
Posts: 939
PB Blaster is your friend. If you can't loosen the nuts or screws, hit it with some PB Blaster and give it a few minutes.

Simple tools should get you done. It's relatively easy to remove the calipers and rotors.


I'd also recommend getting some rubber gloves. The blue ones... the regular yellowish/clear ones are pretty thin, the blue ones are tougher. I recommend this because after changing my brake pads, I had black gunk under my nails for a couple weeks! Makes clean up a lot easier if you use gloves!
__________________
2001 Boxster - Grey on Grey
1969 911T Targa - 'Stinky'

http://www.zoto.com/frayadjacent/img...f27a-4a399.jpg <---- my car. ^ crap I post.

"The existence of the flamethrower is evidence that someone, somewhere once said 'I want to set those people over there on fire, but I don't want to have to walk over there to do it.'"
FrayAdjacent is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 09:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page