Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 12-14-2017, 07:54 AM   #1
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Window drops when I open the door, but then goes back up

Hi All,

I had an oil change yesterday. After picking up my car, I noticed something odd. When I open the driver side door from the outside, the window drops the usual inch or so, but then goes back up to completely closed. So when I close the door, the window hits the frame at the top. However, when I open the same door from the inside, the window drops as normal, and stays down until I close the door. So it seems it's only something weird with the outside door latch.

Any ideas about the cause, or how to reset it?

__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-14-2017, 08:19 AM   #2
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
Have you tried jiggling the door handle? Maybe spray some air into the locking mechanism door jamb side, and into the handle itself. Maybe a shot of some approved lubricant.
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 12-14-2017, 08:26 AM   #3
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
I got a note back from my mechanic:

"I few things come to mind,
is your dome light working correctly?
may try running window all the way down hold a 3-5 seconds then all the way up hold 3-5 seconds
may reset window
if not there is 3(that I can think of) switches that need to work correctly for that system to work properly"

I'm pretty sure the dome light is working properly, but I'll check that. And try this 3-5 second reset.
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-14-2017, 10:21 AM   #4
There Is No Substitute.
 
rick3000's Avatar
 
Join Date: May 2007
Location: West Coast
Posts: 3,253
Garage
Try disconnecting the battery, then putting the windows up/down. You will know if the "reset" worked if you have to hold the window button down to put the windows up/down the first time (one-touch shouldn't work the first time). If that is not it, it could be a faulty microswitch. I don't know if this will work, but you could also try raising and lower the windows by putting the key into the driver's door lock and holding it to the left and right (trust me it works). That may help determine if it the door lock is failing or if it is something else.
__________________
1999 Ocean Blue Metallic Boxster - blueboxster.com

Last edited by rick3000; 12-14-2017 at 10:24 AM.
rick3000 is offline   Reply With Quote
Old 12-14-2017, 11:24 AM   #5
Motorist & Coffee Drinker
 
78F350's Avatar
 
Join Date: Jul 2014
Location: Oklahoma
Posts: 3,652
Garage
I've had & fixed that issue on a couple cars. Recently there was a discussion about buying the VW part (latch mechanism) to fix it much cheaper than the Boxster part. (Just be sure to get either the 8 or 9 pin electrical connector as needed.):
VW do latch/actuator
There is a part in the mechanism that rotates to latch and unlatch the door. That part pushes on a micro switch to let the Central Locking Unit 'know' when the door is unlatched.
On both of mine the rotating latch was made of metal with a plastic coating and the plastic had worn off in the part where the micro switch should contact it.


If you DIY, here's the tech article at Pelican Parts:
Porsche Boxster Door Lock Mechanism / Door Handle - 986 / 987 (1997-08) - Pelican Parts Technical Article
__________________
I am not an attorney, mechanic, or member of the clergy. Following any advice given in my posts is done at your own peril.
78F350 is offline   Reply With Quote
Old 12-14-2017, 11:33 AM   #6
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Well, holding the window down for 5 seconds, then raising again and holding up for 5 seconds did not solve the problem. Tonight after I get home I'll try the battery disconnect. Thanks for the suggestions.

I hate it when the car comes back from the shop with a brand new problem!
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-14-2017, 12:22 PM   #7
Registered User
 
steved0x's Avatar
 
Join Date: Dec 2012
Location: FL
Posts: 4,143
Very odd, my understanding is when the inner or outer door handle is lifted, and the door is closed, the window should drop a little, that is controlled by the 2 microswitches - one for the inner handle and one for the outer handle. The usual problem is the window not dropping, and can be caused by a failure of either of these switches, or the regulator.

Once the door is opened, the window raising back up is controlled by the microswitch in the lock assembly - if the computer thinks the door is closed even when it is open, the window goes right back up as soon as you release either the inner or outer handle.

Odd for you that it only happens when you open the door from the outside.

I am watching this thread to see how it resolves, because maybe I have been thinking about it wrong all these times...
steved0x is offline   Reply With Quote
Old 12-16-2017, 11:48 AM   #8
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Update: Disconnected the battery and left it to sit for a while. Reconnected and tested the windows. No one touch up-down. Then tested the door handles inside and out. Inside still works as it should, but from outside the problem persists.
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-16-2017, 12:13 PM   #9
Registered User
 
MN 986's Avatar
 
Join Date: May 2008
Location: MN
Posts: 327
Garage
I had this issue back in 2009. Here is a link to the thread that helped me resolve it:
Door window drops but immediately jumps back up
MN 986 is offline   Reply With Quote
Old 12-18-2017, 12:12 PM   #10
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Thanks for that link!

Can the microswitch itself be replaced, or will I need to replace the entire lock mechanism?
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-19-2017, 07:20 AM   #11
Registered User
 
Join Date: Oct 2017
Location: New Hope, Pa
Posts: 59
You can replace both inside and outside micro switches......it is not to hard, once you get the door opened up..... I am fighting a "wont drop" issue without much luck so far.... I have replaced the outside handle micro switch, Done the cable tie trick, and replaced the regulator.... With a cheap one.... Which I will likely suffer for.....


Good luck!
F.

Driver outside handle micro switch:

Pelican Parts - European Automotive Parts and Accessories - Porsche • BMW • Mercedes • Volkswagen • Audi • Saab • Volvo • MINI
1096369fred is offline   Reply With Quote
Old 12-20-2017, 08:25 AM   #12
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Update! This morning the inside door latch stopped dropping the window, too. Now no love from either side. Sigh.
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-20-2017, 10:32 AM   #13
Porsche "Purist"
 
Paul's Avatar
 
Join Date: Aug 2003
Location: Wisconsin
Posts: 2,123
Garage
Have you checked the wiring harness connector in the door jam for corrosion?
__________________
1998 Boxster with 7.8 DME, 2005 3.6 liter/325 hp, Variocam Plus, 996 Instrument panel
2001 Boxster original owner. I installed used motor at 89k.
1987 924S. 2002 996TT. PST-2
Owned and repaired Porsches since 1974. Porsche: It's not driving, it's therapy.
Paul is offline   Reply With Quote
Old 12-20-2017, 11:22 AM   #14
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Quote:
Originally Posted by Paul View Post
Have you checked the wiring harness connector in the door jam for corrosion?
No, I'm not familiar with that. Would that account for the wonkiness I've been experiencing? The problem seems intermittent. Earlier today, after opening the trunk lid with the fob, the outside door handle triggered the window drop as it should.
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-20-2017, 01:14 PM   #15
Motorist & Coffee Drinker
 
78F350's Avatar
 
Join Date: Jul 2014
Location: Oklahoma
Posts: 3,652
Garage
I'm still betting on the door latch - either the micro-switch in the latch, or the part of the latch that contacts it. The harness connector in the door jam sounds good too though. All of those micro-switches are wired to the CLU through the door harness.
__________________
I am not an attorney, mechanic, or member of the clergy. Following any advice given in my posts is done at your own peril.
78F350 is offline   Reply With Quote
Old 12-27-2017, 10:42 AM   #16
Registered User
 
Finnegan's Avatar
 
Join Date: Jun 2014
Location: Oregon
Posts: 455
Update! unsmiley face. Mechanic says the door latch needs to be replaced. Many dollars.
__________________
'04 Midnight Blue Metallic 986
Finnegan is offline   Reply With Quote
Old 12-27-2017, 11:57 AM   #17
Registered User
 
Join Date: Oct 2017
Location: New Hope, Pa
Posts: 59
This may be an inexpensive option..... Last week I put the cheap latch in and it worked mechanically..... But the key and lock button didn't work on my car (possible pre existing condition), even though the electrical connector fit (nine pin) on my '98.
I did hook up the old latch which did have partial electrical function and window drop with the key but not
Raise.... Now it doesn't work at all..... I'm thinking I may have blow a fuse or relay..... So stay tuned....

VW do latch/actuator


https://www.ebay.com/itm/VW-OEM-Front-Left-Door-Lock-Latch-Actuator-For-Touareg-Phaeton-PORSCHE-Cayenne/131888303258?_trkparms=aid%3D222007%26algo%3DSIM.M BE%26ao%3D1%26asc%3D20150313114020%26meid%3D8ba4a0 8793044c93ae94ce3af773bcc0%26pid%3D100338%26rk%3D2 %26rkt%3D30%26sd%3D232247573823&_trksid=p2141725.c100338.m3726&rmvSB=true&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover %252F1%252F711-53200-19255-0%252F1%253Fcampid%253D5336391335%2526toolid%253D1 0001%2526mpre%253Dhttps%25253A%25252F%25252Fwww.eb ay.com%25252Fitm%25252FVW-OEM-Front-Left-Door-Lock-Latch-Actuator-For-Touareg-Phaeton-PORSCHE-Cayenne%25252F131888303258%25253F_trkparms%25253Da id%2525253D222007%25252526algo%2525253DSIM.MBE%252 52526ao%2525253D1%25252526asc%2525253D201503131140 20%25252526meid%2525253D8ba4a08793044c93ae94ce3af7 73bcc0%25252526pid%2525253D100338%25252526rk%25252 53D2%25252526rkt%2525253D30%25252526sd%2525253D232 247573823%252526_trksid%25253Dp2141725.c100338.m37 26%2526srcrot%253D711-53200-19255-0%2526rvr_id%253D1398075011600&ul_noapp=true

Last edited by 1096369fred; 12-27-2017 at 12:01 PM.
1096369fred is offline   Reply With Quote
Old 12-30-2017, 04:53 AM   #18
Registered User
 
joecal's Avatar
 
Join Date: Jul 2015
Location: LaGrange Highlands,IL
Posts: 181
Quote:
Originally Posted by 1096369fred View Post
You can replace both inside and outside micro switches......it is not to hard, once you get the door opened up..... I am fighting a "wont drop" issue without much luck so far.... I have replaced the outside handle micro switch, Done the cable tie trick, and replaced the regulator.... With a cheap one.... Which I will likely suffer for.....


Good luck!
F.

Driver outside handle micro switch:

Pelican Parts - European Automotive Parts and Accessories - Porsche • BMW • Mercedes • Volkswagen • Audi • Saab • Volvo • MINI
I'm having the same problem as you with a "won't drop" enough issue, it drops a little but not enough as it should. The electronics in these cars have a lot to be desired.
__________________
1999 Boxster base w/sport package Ocean Blue Metallic/Savanna Beige
joecal is offline   Reply With Quote
Old 12-30-2017, 09:55 PM   #19
Registered User
 
Join Date: Feb 2017
Location: CO
Posts: 989
Have you tried to open and lower the window with the key? Try arming your alarm then off. Insert the key “unlock” the door and hold in place. Both windows should go down. “Lock” the door and hold and both should go up. Sometimes this can reset the handle. Then see if it works.
Geof3 is offline   Reply With Quote
Old 12-30-2017, 11:51 PM   #20
Registered User
 
Join Date: Feb 2017
Location: CO
Posts: 989
Quote:
Originally Posted by joecal View Post
I'm having the same problem as you with a "won't drop" enough issue, it drops a little but not enough as it should. The electronics in these cars have a lot to be desired.
Well, they are almost 20 yrs old...

Geof3 is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 06:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page