Engine tilted.

[jaykay]

Originally Posted by Emerald

Thanks for the feedback! Here's a picture. Looking forward to you're all sage advice, options, and speculation.

pictures

Wow that is a serious droop. Something in the exhaust muffler mount up top must have gone as well. You should be able to see a problem right where the muffler mounts the back to the back of the trans.

I would not drive the car obviously.

[Emerald]

Went under with a friend and carefully examined best we could without seeing anything suspicious. I jacked the drooping pipe and no sound indicating a broken bracket. Called Bill at Pelican and he thinks it’s probably a transmission mount as some of you thought so as well. If the engine etc is only suspended by two trans mounts and one engine mount seems to reason it must be the trans mount on one side. Please correct me if I’m wrong. That being said I’m ready to pull the trigger on a new one(s). Since I do drive hard on bumpy roads both would seem to make sense. Any opinions or experience about the reinforced type ... somewhere between the Wevo and OEM? Any brand of mount recommendations? Maybe anything but OEM would be too stiff for my roads?

[Gilles]

sorry just re read your original post and noticed that you mentioned that the cat is resting on the sway bar, most likely it's due to a worn (or broken) mount...

Have you tried to jack up the engine (with a wooden block) to it's original position?

[Emerald]

Disaster bummer. Exposed everything and found the differential case broke off at the bolt. (of course this is after foolishly buying new transmission mounts). My nephew used to be an instructor and Wyotech and said it would be hard but thinks he can weld it, and add a metal plate for more reinforcement. If we do it I'm going to have him reinforce the other side at the same time. I'm going to do some more research to see if this has ever happened to anyone else before. I googled '986 differentials' and nothing but a 5speed came up. Any advice would be well received.

[Robert986]

Never seen that one before... Have you hit any roadbumps or something that you're aware of?

[piper6909]

Originally Posted by Emerald

Disaster bummer. Exposed everything and found the differential case broke off at the bolt. (of course this is after foolishly buying new transmission mounts). My nephew used to be an instructor and Wyotech and said it would be hard but thinks he can weld it, and add a metal plate for more reinforcement. If we do it I'm going to have him reinforce the other side at the same time. I'm going to do some more research to see if this has ever happened to anyone else before. I googled '986 differentials' and nothing but a 5speed came up. Any advice would be well received.

Something must have been wrong with another mount(s) I can't imagine that such a small aluminum tab with such tiny gussets would be designed to hold so much weight that the motor would drop 2" if it broke.

Is that where the L-shaped part of the tranny mount bolts? If so, is the top bolt of that L-shaped bracket missing? That's the only way I could see something like that happening.

[Gilles]

Emerald, this happen to one of my X1/9 transaxles (where the slave mounts on the tab on top), took the gearbox to a friends shop and they welded the aluminum tab back again and with the extra welds seemed stronger than originally, and never had an issue afterwards, but I had to remove the transaxle to be properly welded..
.

[piper6909]

Originally Posted by Gilles

Emerald, this happen to one of my X1/9 transaxles (where the slave mounts on the tab on top), took the gearbox to a friends shop and they welded the aluminum tab back again and with the extra welds seemed stronger than originally, and never had an issue afterwards, but I had to remove the transaxle to be properly welded..
.

I had one those in high school! Definite chick magnet, but tons of problems!

[Qmulus]

Originally Posted by Emerald

Disaster bummer. Exposed everything and found the differential case broke off at the bolt. (of course this is after foolishly buying new transmission mounts). My nephew used to be an instructor and Wyotech and said it would be hard but thinks he can weld it, and add a metal plate for more reinforcement. If we do it I'm going to have him reinforce the other side at the same time. I'm going to do some more research to see if this has ever happened to anyone else before. I googled '986 differentials' and nothing but a 5speed came up. Any advice would be well received.

Wow, broken transmission case. That must have been quite a hit. That tab is part of the front half of the transaxle assembly including the bell housing and differential housing. I am wondering if the mount bracket or upper mount bosses are broken as well. To do that right, it will have to be removed and disassembled. At that point, you might consider just replacing the whole transmission.

[truegearhead]

Yikes...sorry I led you down the wrong road. I’ve haven’t seen this failure before. Is that an automatic transmission?

[jaykay]

Wow so the case broke right where the trans mount bolts up? Apologies, never thought about that. That explains the angle