Ideas? Sticking clutch pedal only when braking heavily

[Blackroot]

Originally Posted by Oldcarguy

I’m on my iPad and I thought I read your whole post, but I missed your very pertinent point at the bottom. Those 4 pot calipers are holding a lot of fluid under extreme braking. Also, I have no records indicating that the fluid has been changed in the last few years so there may be who knows what in the system.

I’ll try to change the fluid and purge the brake and clutch systems next week. I’ll update as soon as I have the result.

I just used one of these with fantastic results. I did it dry @ 22PSI
https://www.amazon.com/Motive-Products-European-Bleeder-Pressure/dp/B0002KM5L0

Be quick on the bleeder or you will drain the brake fluid tank.
I'm a weekend warrior, like you

[Oldcarguy]

Originally Posted by Blackroot

I just used one of these with fantastic results. I did it dry @ 22PSI
https://www.amazon.com/Motive-Products-European-Bleeder-Pressure/dp/B0002KM5L0

Be quick on the bleeder or you will drain the brake fluid tank

My Motive just came in. I’ll have my shop assistant (wife) monitoring to ensure I don’t introduce new air into the system.

[Blackroot]

Originally Posted by Oldcarguy

My Motive just came in. I’ll have my shop assistant (wife) monitoring to ensure I don’t introduce new air into the system.

You can either use the bleeder screw on the slave cylinder or a brake caliper.
I would start with slave.
11mm socket, and be ready to get soaked unless you attached a hose to the bleeder valve to a tray.
Brake fluid actually doesn't taste bad, but don't swallow
Tight quarters.
Make sure the brake fluid tank is completely full
Also, start with clutch fully up, pump the bleeder tank to 22psi. get under car and open bleeder.
When air noise stops and a steady stream suddenly appears, tighten valve.
Get in car and try clutch pedal (fill the brake fluid tank first as it will have lowered)
Might be perfect right there.
If not, repeat

[Oldcarguy]

Originally Posted by Blackroot

You can either use the bleeder screw on the slave cylinder or a brake caliper.
I would start with slave.
11mm socket, and be ready to get soaked unless you attached a hose to the bleeder valve to a tray.
Brake fluid actually doesn't taste bad, but don't swallow

Duly noted

[Blackroot]

Originally Posted by Oldcarguy

Duly noted

I edited below, so here it was

Make sure the brake fluid tank is completely full
Also, start with clutch fully up, pump the bleeder tank to 22psi. get under car and open bleeder.
When air noise stops and a steady stream suddenly appears, tighten valve.
Get in car and try clutch pedal (fill the brake fluid tank first as it will have lowered)
Might be perfect right there.
If not, repeat

[Blackroot]

Originally Posted by Blackroot

I edited below, so here it was

Make sure the brake fluid tank is completely full
Also, start with clutch fully up, pump the bleeder tank to 22psi. get under car and open bleeder.
When air noise stops and a steady stream suddenly appears, tighten valve.
Get in car and try clutch pedal (fill the brake fluid tank first as it will have lowered)
Might be perfect right there.
If not, repeat

I tried the Pelican way with starting the bleed process with clutch pedal down and never had any luck, BTW.
Nothing against Pelican as they are tremendously valuable, and I source them for almost everything I do.
Up always worked for me.

[Oldcarguy]

Originally Posted by Blackroot

I tried the Pelican way with starting the bleed process with clutch pedal down and never had any luck, BTW.
Nothing against Pelican as they are tremendously valuable, and I source them for almost everything I do.
Up always worked for me.

Thanks. I’ve also read and seen videos doing the clutch bleed both ways. Because I’ll be doing a pressure bleed, pedal up seems most intuitive to me also.