Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 07-07-2018, 11:17 AM   #1
Registered User
 
gabedrummin's Avatar
 
Join Date: Jan 2018
Location: Houston
Posts: 221
Garage
I don't think its limited slip.Is there any to know without opening it up?
gabedrummin is offline   Reply With Quote
Old 07-07-2018, 11:32 AM   #2
Registered User
 
911monty's Avatar
 
Join Date: Oct 2014
Location: California Central Coast
Posts: 1,476
Garage
With rear of car on jackstands and in gear, grab a wheel and rotate. If open differential the other wheel will turn in the opposite direction. An LSD will attempt to rotate the other wheel in the same direction.

You can check your option codes under hood. If factory should have IIRC code 220.

Last edited by 911monty; 07-07-2018 at 11:44 AM.
911monty is offline   Reply With Quote
Old 07-11-2018, 08:59 AM   #3
Registered User
 
gabedrummin's Avatar
 
Join Date: Jan 2018
Location: Houston
Posts: 221
Garage
It is an open diff.
gabedrummin is offline   Reply With Quote
Old 07-11-2018, 09:08 AM   #4
Registered User
 
BYprodriver's Avatar
 
Join Date: Oct 2008
Location: O.C. CA
Posts: 3,709
Garage
Quote:
Originally Posted by gabedrummin View Post
I don't think its limited slip.Is there any to know without opening it up?
Look for the receipt, I don't think any 986's came with limited slip.
__________________
OE engine rebuilt,3.6 litre LN Engineering billet sleeves,triple row IMSB,LN rods. Deep sump oil pan with DT40 oil.
BYprodriver is offline   Reply With Quote
Old 07-11-2018, 12:00 PM   #5
98 Arctic silver 986
 
tommy583's Avatar
 
Join Date: Jul 2011
Location: Upstate, NY
Posts: 1,452
Garage
Worn center motor mount can cause these noises as well. Mine sounded like a bad CV joint when cornering hard. With new mount the noise is gone. Since your getting a new engine i'd imagine that's the perfect time to install a new mount.
tommy583 is offline   Reply With Quote
Old 08-20-2018, 09:28 AM   #6
Thom
 
Join Date: Jan 2016
Location: Florida
Posts: 41
Garage
Same noise issue

I too replaced the complete drive shaft CV joints, all suspension parts AND last weekend I did both rear wheel bearings. The only thing I haven't done is to replace all the bushings for the swaybar.

How difficult is replacing the center motor mount? Is this a DIY type of project? I do have access to a full lift and tool system.

Thanks
Thom
Calmg0d is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 10:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page