Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 10-09-2010, 04:49 AM   #1
Carnut
 
AndyA6's Avatar
 
Join Date: May 2010
Location: Utah
Posts: 775
It looks like a problem with the bleeder valve..... too much residue and fairly wet around that area, valve was/is closed.
I checked after a short drive, seems that the valve isn't holding.



Quote:
Originally Posted by Burg Boxster
the latest cap version is .04 but generally speaking, the .01 thur .04 designs are very similar. The .00 design was vastly different and very weak (had a rounded inner flange).

If you've already checked under the carpet and barring any other signs of a leak, and if the cap is on tight (the p/n should be a the 6 o'clock position when standing at rear of car) you're in all likely-hood good to go. For the sake of argument though, remove the coolant cap, oil filler cap, and black cover plate below them (it'll pry right up) . Check the coolant tank bleeder valve (a black cap w/ what looks like 1/2 of a binder clip on top) and make sure it's in the down/locked (parallel to the road) position and there isn't any (more than a possible trace) white residue around it. If in doubt, you can have (almost any shop) run a quick pressure test on the cooling system (about 20min).

FWIW, I used to get similar condensation occasionally, depending on climate conditions, w/ my '99 Boxster but never had any issues.

__________________
'14 Boxster
AndyA6 is offline   Reply With Quote
Old 10-09-2010, 06:01 AM   #2
07 Carrera S Cab
 
Boxtaboy's Avatar
 
Join Date: Nov 2005
Location: New Jersey
Posts: 2,273
Garage
In that case, you should replace the o-ring seal in the bleeder valve. When retorquing the bleeder valve bolts, don't over tighten them as they screw into plastic.
__________________
Current: 07 Carrera S Cab in Midnight Blue

Previous: 01 Boxster in Arctic Silver, 86 944 in Guards Red
Boxtaboy is offline   Reply With Quote
Old 10-09-2010, 11:05 AM   #3
Carnut
 
AndyA6's Avatar
 
Join Date: May 2010
Location: Utah
Posts: 775
Well, took the top of the bleeder valve off.

First of all, these screws were not really tight, barely handtight.

Everything inside looked totally ok, no rips, dirt or any other damage. I cleaned everything and screwed the top back on.

Judging by the residue and the coolant leaking it seems to me that the top simply wasn't tight enough.

After a short drive it looks like all is ok but I will report back later.
__________________
'14 Boxster
AndyA6 is offline   Reply With Quote
Old 10-09-2010, 12:47 PM   #4
Porscheectomy
 
Join Date: Mar 2006
Location: Seattle Area
Posts: 3,011
Quote:
Originally Posted by AndyA6
Well, took the top of the bleeder valve off.

First of all, these screws were not really tight, barely handtight.

Everything inside looked totally ok, no rips, dirt or any other damage. I cleaned everything and screwed the top back on.

Judging by the residue and the coolant leaking it seems to me that the top simply wasn't tight enough.

After a short drive it looks like all is ok but I will report back later.
The bleeder valve comes in two parts. There's the part with the valve on it, and then there's a collar. The screws run through the cap and collar and "bite" into the tank. The collar has two o-rings that seal it to the tank. The're side seal, so screw torque doesn't effect their seal. When mine leaked, it only happened occasionally. If you take off the cap and tug and wiggle at the collar, you can get it off and replace the o-rings.
blue2000s is offline   Reply With Quote
Old 10-09-2010, 02:32 PM   #5
Carnut
 
AndyA6's Avatar
 
Join Date: May 2010
Location: Utah
Posts: 775
Thanks! Makes perfect sense.

After cleaning / re-installing and another spirited canyon drive it seems to have made a difference, no leak/condensation
I was very careful with those screws, only tightened by hand.


Still keeping an eye on it.

Later,
Andy
__________________
'14 Boxster
AndyA6 is offline   Reply With Quote
Old 09-25-2011, 10:25 AM   #6
Carnut
 
AndyA6's Avatar
 
Join Date: May 2010
Location: Utah
Posts: 775
Quote:
Originally Posted by AndyA6 View Post
Thanks! Makes perfect sense.

After cleaning / re-installing and another spirited canyon drive it seems to have made a difference, no leak/condensation
I was very careful with those screws, only tightened by hand.


Still keeping an eye on it.

Later,
Andy


OK, after this summer season I am happy to report that there is no more condensation. Dust dry.

I guess the best lesson here is "drive your car!"
__________________
'14 Boxster
AndyA6 is offline   Reply With Quote
Old 09-25-2011, 12:02 PM   #7
Registered User
 
Join Date: Dec 2010
Location: Hot Springs Village, Arkansas
Posts: 245
Here are a couple pics of the o-rings under the bleeder valve.

First remove the bleeder valve screws and take off the top part. The base with the screw holes looks like it's part of the tank but it's actually a separate piece. Take a big pair of channelocks and wiggle it a little, then pull it straight up.

This is what's under the base and where the two o-rings live. It fixed mine for a few months. No condensation but this past summer the tank cracked on the bottom so the parts you see are no longer on my car.
Dale_K is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 04:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page