new clutch, what else can be replaced?

[Perfectlap]

don't worry the dealer price quotes were for ****************s and giggles. The price of the dealer doing clutch, brakes and suspension will buy you another used Boxster.
I think they wanted $300 for a coolant flush and $400 to replace the 02 sensors (just labor). LOL
I intend to use an indy shop. They did the 02's and a fuel filter for $130. Wish I had a lift... I'm going back to flush the brakes and coolant.
My boots are definitely torn, which explains why the dealer simply added the cost of a whole new unit. The service manager must have spotted the Bentley manual or my OBD II in the trunk because he said goodbye just as quickly as he gave me the prices.

"Oh, and I’ll guarantee you that a dealer will not install the LN IMS upgrade, all they will install is a new OEM IMS unit, which will put you right back in the land of not knowing when it is going to fail. The reason a dealer will not do the LN unit is that installing one would be tantamount to and admission that the OEM version has a potential problem; so they won’t do it……………….."


I see you are at it again! Always over the top without facts! I'll call your "guarantee" :

http://lnengineering.com/service.html

Joe Rizza Porsche in Orland Park, IL has partnered with LN Engineering to offer our complete line of products and services for your 1997-2008 Porsche Boxster, Cayman, and 911. Call Jerry at (708) 364-2259 to make an appointment today. Tell him Charles sent you!

[coreseller]

I'm in the middle of doing what you are talking about. JFP is right on the axle issue, deal with boots and repacking if needed. I've read where the AOS is an easy R&R if it is becoming an issue or you are concerned, the tranny will be out of the way. Best price I've found on Sachs OEM Clutch Kit:

http://cgi.ebay.com/ebaymotors/00-04-BOXSTER-S-3-2L-3-2-PORSCHE-SACHS-NEW-CLUTCH-KIT_W0QQcmdZViewItemQQhashZitem19b9fa568eQQitemZ11 0494373518QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAcce ssories

LNS Bearing $519 (Single Row) plus $70 for R&R Tool Kit from Jake Raby. I've found the Boxster to be very easy to work on if you take your time and do your research first. Heck, I replaced the ignition switch last week and found out just how many things were screwed up electrically now that they're all working correctly lol. Good Luck.

[gschotland]

[QUOTE=coreseller]Best price I've found on Sachs OEM Clutch Kit:

http://cgi.ebay.com/ebaymotors/00-04-BOXSTER-S-3-2L-3-2-PORSCHE-SACHS-NEW-CLUTCH-KIT_W0QQcmdZViewItemQQhashZitem19b9fa568eQQitemZ11 0494373518QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAcce ssories

That one's for an S. Didn't notice whether Perfectlap has an S. Either way, I think you're doing pretty well if you can find the Sachs kit for <$400.

Are you planning to replace your flywheel while you're at it? My original clutch still had some life left on it at 70k. The flywheel didn't look great, so Jake recommended replacement. I got a new one from a friend who'd sold his car. When I was shopping (before I got my friend's), this was about the best deal I could find on an OEM type unit:

http://cgi.ebay.com/ebaymotors/Porsche-Boxster-2002-LuK-Dual-Mass-Flywheel-DMF042_W0QQcmdZViewItemQQhashZitem35a75e37b9QQitem Z230441236409QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fA ccessories

Given all the other money you're spending to do the job right, this is probably not the place to save ~$450. Dial up the LuK website to make sure you're getting the correct model for your 2000.

[986FortyEight]

just did the RMS, IMS Retrofit, Lightweight Flywheel, Spec clutch, changed all bearings and other clutch parts; and finally, the front main seal. I noticed mine had started to leak some as well.
I am going to check the boots, and definitely change the wheel bearings while I am in there.

[coreseller]

[QUOTE=gschotland][QUOTE=coreseller]Best price I've found on Sachs OEM Clutch Kit:

http://cgi.ebay.com/ebaymotors/00-04-BOXSTER-S-3-2L-3-2-PORSCHE-SACHS-NEW-CLUTCH-KIT_W0QQcmdZViewItemQQhashZitem19b9fa568eQQitemZ11 0494373518QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAcce ssories

That one's for an S. Didn't notice whether Perfectlap has an S. Either way, I think you're doing pretty well if you can find the Sachs kit for <$400.

Figured Mr. PerfectLap had an "S" per the center intake inlet. No Matter....Either way, think about how fortunate we are to have Charles at LN Engineering and Jake Raby to help us non tech guys out....seriously. These guys have put forth the effort and knowledge to see to it that enthusiasts like us can further our passions without the potential depth of pain.