A Division of Pelican Parts

986 Boxster Catalog | 987 Cayman Catalog | Accessories | Performance


Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Search Forums
Reload this Page Search Results
Register Garage FAQ Community Calendar Today's Posts Search

Page 1 of 6 1 2 3 Last »
Showing results 1 to 25 of 150
Search took 0.03 seconds. Search: Posts Made By: paulv
Forum: Boxster General Discussions 02-06-2015, 06:32 AM
Replies: 5
Views: 1,830
Posted By paulv
In the Actual Values selections (IIRC, in the PSM...

In the Actual Values selections (IIRC, in the PSM subsystem) -- I use Durametric version 6. Select the 4 wheels and set recording, then take a very short ride get gather data.


I don't know about...
Forum: Performance and Technical Chat 11-20-2014, 04:35 AM
Replies: 11
Views: 1,485
Posted By paulv
I would agree with what Topless recommended --...

I would agree with what Topless recommended -- the freeze frame data looks good with respect to fuel trims and the code was set at idle/low load and not at high rpms/high load.

Although it's not...
Forum: Performance and Technical Chat 11-18-2014, 08:45 AM
Replies: 11
Views: 1,485
Posted By paulv
Those two codes are for a lean condition at idle...

Those two codes are for a lean condition at idle (both banks).

Since you have some kind of OBD2 tool, does it provide Freeze Frame data? FF data gets captured when the CEL is set and has most of...
Forum: Boxster General Discussions 11-04-2014, 08:03 AM
Replies: 4
Views: 1,723
Posted By paulv
P1124 is a fuel pump relay code and if it's...

P1124 is a fuel pump relay code and if it's faulty, it could cause the engine to starve for gas causing a lean condition (thus the P1126 bank 1, but I would expect P1133, bank 2 to be set also).
...
Forum: Performance and Technical Chat 10-08-2014, 10:16 AM
Replies: 3
Views: 1,136
Posted By paulv
PM sent. Regards, paul...

PM sent.

Regards,
paul...
Forum: Boxster General Discussions 10-02-2014, 09:23 AM
Replies: 2
Views: 847
Posted By paulv
The P0410/1411 are related to the secondary air...

The P0410/1411 are related to the secondary air system (both banks), implausible signal.

For the O2 sensor problem, try swapping the forward sensor (that you just replaced) with the forward sensor...
Forum: Boxster General Discussions 07-17-2014, 05:06 AM
Replies: 2
Views: 1,405
Posted By paulv
P0343 is the Cam Position Sensor (Bank 1) above...

P0343 is the Cam Position Sensor (Bank 1) above signal limit.

Sent you a PM.

Regards,
paul...
Forum: Boxster General Discussions 07-15-2014, 07:06 AM
Replies: 8
Views: 1,380
Posted By paulv
Welcome!

Markus,

Welcome to the forum!!

Not only will you get ideas on projects, but there are many knowledgeable people here to help with any problems you may encounter.

Regards,
paul...
Forum: Performance and Technical Chat 07-11-2014, 03:57 AM
Replies: 7
Views: 3,622
Posted By paulv
Richard, You didn't mention your MY, so I'll...

Richard,

You didn't mention your MY, so I'll assume that your DME is version 7.2.

For a P1130, there are several fault areas to look for (as you know, that code applies to idle range only):
...
Forum: Performance and Technical Chat 04-29-2014, 10:33 AM
Replies: 3
Views: 2,152
Posted By paulv
I've assumed that your do this for your '00...

I've assumed that your do this for your '00 Boxster ( which is DME 7.2). The oil temperature is checked by the DME because codes P0197 and P0198 are thrown for below/above limits (oil temp is used...
Forum: Performance and Technical Chat 04-25-2014, 10:12 AM
Replies: 3
Views: 2,551
Posted By paulv
PM sent. Regards, paul...

PM sent.

Regards,
paul...
Forum: Boxster General Discussions 02-12-2014, 04:24 AM
Replies: 13
Views: 1,309
Posted By paulv
JD, Thx for the finance tip -- I have $2.5M...

JD,

Thx for the finance tip -- I have $2.5M hanging around so I just have to finance the remaining $100K. After I buy it, I'll have it painted Speed Yellow in your honor.

Regards,
paul...
Forum: Boxster General Discussions 02-12-2014, 04:19 AM
Replies: 24
Views: 1,998
Posted By paulv
Which sax do you play (e.g., soprano, alto,...

Which sax do you play (e.g., soprano, alto, etc.)?

Regards,
paul...
Forum: Boxster General Discussions 12-17-2013, 07:46 AM
Replies: 18
Views: 2,222
Posted By paulv
Since P0154 is an "Interruption of Signal" on the...

Since P0154 is an "Interruption of Signal" on the upstream O2 sensor (Bank 2) this could be a wiring problem (signal or ground) or the O2 sensor itself. Sounds like this problem could also cause the...
Forum: Performance and Technical Chat 12-13-2013, 09:54 AM
Replies: 13
Views: 8,231
Posted By paulv
Does your service manual discuss what criteria...

Does your service manual discuss what criteria has to be met before the SAI readiness test can begin? I know for my '07, there's about 6-8 items that need to be met first.

Regards,
paul....
Forum: Boxster General Discussions 12-06-2013, 07:54 AM
Replies: 27
Views: 2,191
Posted By paulv
Durametric modeled their tool to give give the...

Durametric modeled their tool to give give the same units of measure that the factory (PIWIS) tools gives since the values outputted have those units.

Regards,
paul...
Forum: Boxster General Discussions 11-08-2013, 04:34 AM
Replies: 5
Views: 1,744
Posted By paulv
If he did that, then don't expect him to properly...

If he did that, then don't expect him to properly troubleshoot your problem -- pulling the codes is the first step of the diagnostics and he shouldn't have reset them. Now you don't have the codes...
Forum: Performance and Technical Chat 11-05-2013, 09:01 AM
Replies: 4
Views: 1,721
Posted By paulv
Bill, Here are potential faults for that...

Bill,

Here are potential faults for that code:

– Incorrect signal from MAF sensor
– Intake air system leaking
– Fuel pressure too low
– Volume supply of fuel pump too low
– Fuel injectors...
Forum: Performance and Technical Chat 10-29-2013, 09:18 AM
Replies: 1
Views: 1,235
Posted By paulv
The vehicle info is stored in the firmware that's...

The vehicle info is stored in the firmware that's inside the connector. The overevs info is in the DME selection (Engine Module) under (IIRC) either Identification or Information selections.
...
Forum: Boxster General Discussions 09-25-2013, 03:43 AM
Replies: 13
Views: 2,719
Posted By paulv
As JD mentioned earlier, there could be wiring...

As JD mentioned earlier, there could be wiring issues -- an intermittent open circuit or short to ground. Also, according to wiring diagrams, there's an ECM relay that is powered from pin 27 of the...
Forum: Boxster General Discussions 09-04-2013, 03:44 AM
Replies: 8
Views: 1,392
Posted By paulv
The CEL only comes on when emissions exceed the...

The CEL only comes on when emissions exceed the Federal test standards by 1.5.

You could easily buy a voltage gauge and hook it up to the battery -- many parts shops sell these.

Regards,...
Forum: Boxster General Discussions 08-30-2013, 03:22 AM
Replies: 9
Views: 2,288
Posted By paulv
Some code info (applicable to a 2002, DME 7.2...

Some code info (applicable to a 2002, DME 7.2 Boxster):

P0107 diags says the DME has failed (ambient pressure sensor is incorporated into the DME due to a short circuit to ground

P0343 diags...
Forum: Performance and Technical Chat 08-29-2013, 09:14 AM
Replies: 7
Views: 2,668
Posted By paulv
You certainly do need a new coil pack. You may...

You certainly do need a new coil pack. You may still want to watch the misfires in the actual values to see if thee are other cylinders that are misfiring but not enough to reach the threshold to...
Forum: Performance and Technical Chat 08-29-2013, 06:43 AM
Replies: 7
Views: 2,668
Posted By paulv
I don't know if the older version of Durametric...

I don't know if the older version of Durametric has Freeze Frame data access. If so, check that and post it here. Misfires are not necessarily caused by ignition issues -- can be mechanical or fuel...
Forum: Boxster General Discussions 08-29-2013, 03:51 AM
Replies: 9
Views: 2,288
Posted By paulv
Check with your tool which DTC set the CEL, then...

Check with your tool which DTC set the CEL, then go from there. Also, you can view the misfires as the car is running. Do you have service info? Because you're going to need what the test criteria...
Showing results 1 to 25 of 150
Page 1 of 6 1 2 3 Last »

 
Forum Jump


All times are GMT -8. The time now is 05:33 PM.

Contact Us - Pelican Parts Porsche Catalog - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page