08-29-2020, 12:15 PM
|
#21
|
Registered User
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,848
|
to isolate the noise of the drivetrain (engine/transmission) from the chassis, find a long downhill, turn off the engine and let it coast downhill if the noise still there is chassis related most likely a bearing or a sticking caliper...
.
|
|
|
08-29-2020, 02:32 PM
|
#22
|
Registered User
Join Date: Dec 2019
Location: New York
Posts: 10
|
So I found today on my drive that when the car is turning to the left on a curve or such the noise and vibration almost goes away. When going to the right it gets worse. Only enough worse though that I haven't noticed it until actually paying attention to it. Any ideas based off of this new information? ALSO... thanks so much to everyone that has responded and helped. I am continually amazed by the helpfulness and friendliness of the Porsche community.
|
|
|
08-29-2020, 02:36 PM
|
#23
|
Registered User
Join Date: Dec 2019
Location: New York
Posts: 10
|
Quote:
Originally Posted by 519AutoTech
To eliminate possible wheel bearing issues, simply swerve left and right while driving with the noise present. If the sound changes, its wheel bearings. If the sound remains constant, its in the drivetrain or wheels/tires. Hope you resolve the issue
|
Just did this, noise almost stops completely when slightly turning to the left. Gets worse when turning to the right. Does this mean rear driver side wheel bearing is bad?
|
|
|
08-29-2020, 03:23 PM
|
#24
|
Registered User
Join Date: Sep 2008
Location: Florida
Posts: 2,492
|
Quote:
Originally Posted by RA1
Just did this, noise almost stops completely when slightly turning to the left. Gets worse when turning to the right. Does this mean rear driver side wheel bearing is bad?
|
Do both. At this mileage, you're going to do both eventually anyway. This is a driveway job if you're handy. Wheel bearings are under $50 each. Pull your wheel hub and press out the bearing. If you don't have a press, go to a garage or auto parts store and have them press out the old and in the new. Not bad.
|
|
|
08-29-2020, 07:12 PM
|
#25
|
Registered User
Join Date: Aug 2018
Location: Woodland Wa
Posts: 1,291
|
Way to use your senses.
See, hear, feel, smell, taste, your car when you drive it.
Then you start to sense things before they happen.
Now you have a direction to go.
Replacing bearings is not hard.
Let us know how things turn out.
|
|
|
08-31-2020, 04:34 AM
|
#26
|
01 Boxster S
Join Date: Jun 2020
Location: Windsor
Posts: 14
|
Quote:
Originally Posted by RA1
Just did this, noise almost stops completely when slightly turning to the left. Gets worse when turning to the right. Does this mean rear driver side wheel bearing is bad?
|
It sounds like a left side bearing for sure. As to which one, you may have to use your "senses" as someone mentioned
|
|
|
08-31-2020, 08:12 AM
|
#27
|
Registered User
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,848
|
By removing the drive shafts you would be able to replace the bearings in site (without having to remove the hub) this way you will minimize the risk of damaging the ball joint rubber boot and the need to realign the rear axle.
You may want to borrow a wheel bearing removing tool or borrow a sledge hammer from Autozone (it will be a workout...)
Please note that the bearings have a magnetic strip on one end (for the ABS) and you want to install them the proper way, I learned about this the hard way..
Good luck
Last edited by Gilles; 08-31-2020 at 12:35 PM.
Reason: Spanglish..sorry
|
|
|
08-31-2020, 09:31 AM
|
#28
|
Registered User
Join Date: Oct 2008
Location: O.C. CA
Posts: 3,709
|
Quote:
Originally Posted by 519AutoTech
It sounds like a left side bearing for sure. As to which one, you may have to use your "senses" as someone mentioned
|
Easiest way to do this is to drive next to a wall at night when it's quiet outside, the wall will bounce the sound back to you louder on the bad side bearing.
__________________
OE engine rebuilt,3.6 litre LN Engineering billet sleeves,triple row IMSB,LN rods. Deep sump oil pan with DT40 oil.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
All times are GMT -8. The time now is 11:14 AM.
| |