Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 04-27-2018, 07:04 AM   #1
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
2 (probably) dumb questions

Hello Forum,
I have 2 (probably) dumb questions that I would like to get some clarity on.
I have read and re-read most of the threads on these subjects, but can't quite get my head around the answers.
So here goes:

The car is a 2002 Base with 150K

1. To replace the external chain tensioners only, do the engine and the cams need to be locked at TDC or can I just unscrew the old tensioners and screw in the new ones?

2. To replace the inner tie rods, it appears to me that there is a ball joint in front of the part where a wrench would lock onto the rod to thread it into place. Would this type of tool work? I don't understand how it would go around the ball joint to reach the tabs on the inner part of the tie rod to thread it in. For that matter, I'm not clear on how any of these tools get around/over the ball joint.
I can't visualize how this works!
Some have mentioned the Harbor Freight Tie Rod Tool and others Wayne's book suggests channel locks or a plumbers wrench. Not sure which tool to get or use.

Thanks

Rob

Attached Images
 

Last edited by robdelorenzo; 04-27-2018 at 07:27 AM.
robdelorenzo is offline   Reply With Quote
Old 04-27-2018, 07:55 AM   #2
Registered User
 
Join Date: Dec 2016
Location: Clifton, NJ
Posts: 1,135
No clue on the first one, but on the tie rod, I'm not sure how the hell that tool would work. In a pinch, channel locks should work fine on the inner, but its tight in there and you might have a hard time getting leverage, especially on jackstands.

I bought the harborfreight tie rod tool and it works a treat. Makes it a totally trivial task.
Quadcammer is offline   Reply With Quote
Old 04-27-2018, 08:00 AM   #3
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
Thanks Quadcammer.
Just to be clear, it's this Harbor Freight Tool?
I'm glad they bombard me with 25% off discount coupons!
robdelorenzo is offline   Reply With Quote
Old 04-27-2018, 08:08 AM   #4
Registered User
 
Join Date: Dec 2016
Location: Clifton, NJ
Posts: 1,135
thats the one. You use the 1 1/4" insert. Depending on what replacement tie rods you buy, you may have to grind a different insert to fit a bit, but it didn't take much. Well worth the $40 or so.
Quadcammer is offline   Reply With Quote
Old 04-27-2018, 08:27 AM   #5
Registered User
 
kk2002s's Avatar
 
Join Date: Sep 2012
Location: S. New Jersey
Posts: 1,239
Garage
Quote:
Originally Posted by robdelorenzo View Post
Thanks Quadcammer.
Just to be clear, it's this Harbor Freight Tool?
I'm glad they bombard me with 25% off discount coupons!
+1 Harbor Freight Inner Tie rod Tool. I like because it allows you to use a torque wrench to tighten

As far a Tensioners, from what I've read TDC takes pressure off chains. If I ever did this job I would lock the cams because I'm a chicken and would be terrified that the cams might skip timing
__________________
2002 S - old school third pedal
Seal Grey
kk2002s is offline   Reply With Quote
Old 04-27-2018, 08:31 AM   #6
Registered User
 
Join Date: Feb 2005
Location: It's a kind of magic.....
Posts: 6,261
Quote:
Originally Posted by robdelorenzo View Post
Hello Forum,
I have 2 (probably) dumb questions that I would like to get some clarity on.
I have read and re-read most of the threads on these subjects, but can't quite get my head around the answers.
So here goes:

The car is a 2002 Base with 150K

1. To replace the external chain tensioners only, do the engine and the cams need to be locked at TDC or can I just unscrew the old tensioners and screw in the new ones?

2. To replace the inner tie rods, it appears to me that there is a ball joint in front of the part where a wrench would lock onto the rod to thread it into place. Would this type of tool work? I don't understand how it would go around the ball joint to reach the tabs on the inner part of the tie rod to thread it in. For that matter, I'm not clear on how any of these tools get around/over the ball joint.
I can't visualize how this works!
Some have mentioned the Harbor Freight Tie Rod Tool and others Wayne's book suggests channel locks or a plumbers wrench. Not sure which tool to get or use.

Thanks

Rob
1. The engine should be locked at TDC, and the cams locked as well. You have a three chain engine, which is the most sensitive to jumping time, so take the necessary precautions.

2. That is wrong tool. You need an appropriate inner ball joint tool that slides on after the outer tie rod end is removed. We use a Mayhew Pro in the shop that automatically adjusts to any type of inner (pricey, but very useful):

__________________
Anything really new is invented only in one’s youth. Later, one becomes more experienced, more famous – and more stupid.” - Albert Einstein
JFP in PA is offline   Reply With Quote
Old 04-27-2018, 09:36 AM   #7
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
Thanks JFP.
This board is the best!
robdelorenzo is offline   Reply With Quote
Old 04-29-2018, 05:27 AM   #8
Registered User
 
mikesz's Avatar
 
Join Date: Feb 2013
Location: Cranston RI
Posts: 902
Garage
I just did my inner and outer tie rods and used the HF tool to put new ones on and rented tool from Advanced auto parts to get old one off. Worked fine.
__________________
99 Porsche Boxster
mikesz is offline   Reply With Quote
Old 04-29-2018, 06:32 AM   #9
Registered User
 
Join Date: Jul 2017
Location: Tucson AZ
Posts: 536
Do you have a manual, follow the directions in the manual for the chain tensioners. No substitution for the FSM. I think I'd lock the crank at TDC, it's an easy enough process. And from what I've seen inside the engine, the timing isn't likely to jump.

Wayne's book is wonderful, and at $22 at Amazon, it's such a bargain. But sometimes you need to consult the factory manual.
__________________
2001 Boxster
2007 Toyota Highlander
2003 New Beetle Convertible, Turbo, Tip 6 speed
Brian in Tucson is offline   Reply With Quote
Old 04-29-2018, 08:44 AM   #10
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
Thanks for all the help.
By "manual" do you mean The Bentley One?
That's next on my list, since I have 101 Projects, but sometimes it's a tad thin on the details.

Other obvious questions are then is which tools is the best ones (other than the gold plated $300 Porsche ones) to remove the ball joints on the coffin arms and to lock the cams.

I have seen videos where people have made their own cam locking tools, or am I being foolish trying to save $100?

thanks

Rob
robdelorenzo is offline   Reply With Quote
Old 04-30-2018, 06:04 AM   #11
Registered User
 
Join Date: Dec 2009
Location: Orange County, CA
Posts: 1,843
Quote:
Originally Posted by robdelorenzo View Post
Other obvious questions are then is which tools is the best ones (other than the gold plated $300 Porsche ones) to remove the ball joints on the coffin arms and to lock the cams.

I have seen videos where people have made their own cam locking tools, or am I being foolish trying to save $100?

thanks

Rob
Rob, buy the cam locking tools, all the other ones that you may need should be already on your toolbox, to remove the ball joints, 'borrow one' from Autozone, it works great.

Good luck!
Gilles is offline   Reply With Quote
Old 04-30-2018, 07:18 AM   #12
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
Great. I'm ordering the parts from Pelican and this will be next weekend's project!
robdelorenzo is offline   Reply With Quote
Old 05-01-2018, 07:24 AM   #13
Registered User
 
Join Date: Mar 2017
Location: Los Angeles
Posts: 356
Next question!

Thanks for all the sage advice.
I just got off the phone with my trusty Pelican Parts Specialist (Hi Katy!) and am ordering the parts to refresh the front end. Both Tie rods, control arms, coffin arms, nuts and bolts.
But when trying to order the boots for the steering column, apparently there are different ones depending on the steering rack #
How do I find that #?
We were unable to determine it from the VIN
The car is an 02 Base
As always, your help is appreciated!

robdelorenzo is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 08:57 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page