Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 07-03-2014, 10:35 AM   #1
Registered User
 
Pdwight's Avatar
 
Join Date: May 2013
Location: North Alabama
Posts: 2,079
Second cat delete pipes.....Wrap ??

If you were going to delete the secondary Cats would you wrap the cat delete pipes or leave them ??

Pdwight is offline   Reply With Quote
Old 07-03-2014, 10:52 AM   #2
Registered User
 
BYprodriver's Avatar
 
Join Date: Oct 2008
Location: O.C. CA
Posts: 3,709
Garage
Wrapping is good, ceramic coating inside & out is so much better.

__________________
OE engine rebuilt,3.6 litre LN Engineering billet sleeves,triple row IMSB,LN rods. Deep sump oil pan with DT40 oil.
BYprodriver is offline   Reply With Quote
Old 07-03-2014, 10:56 AM   #3
Certified Boxster Addict
 
Join Date: Nov 2010
Location: Los Angeles
Posts: 7,669
As far as I am aware, there is no particular reason to wrap the cat delete pipes. The stock cat pipes are not wrapped and there is sufficient heat shielding under the car. All of the pipes that I have seen (along with the primary cat delete pipes on my Spec Boxster) are not wrapped.

On the other hand, I am not aware of any particular reason not to wrap them if you wanted to try and cut down the radiated heat around the engine area.
__________________
1999 996 C2 - sold - bought back - sold for more
1997 Spec Boxster BSR #254
1979 911 SC
POC Licensed DE/TT Instructor
thstone is offline   Reply With Quote
Old 07-03-2014, 11:22 AM   #4
Registered User
 
BYprodriver's Avatar
 
Join Date: Oct 2008
Location: O.C. CA
Posts: 3,709
Garage
Hotter air flows faster, my trunk stays much cooler too. Ceramic coating headers has to reduce oil temp in the heads where the pipe nearly touches the chain housing.
__________________
OE engine rebuilt,3.6 litre LN Engineering billet sleeves,triple row IMSB,LN rods. Deep sump oil pan with DT40 oil.
BYprodriver is offline   Reply With Quote
Old 07-03-2014, 11:34 AM   #5
Registered User
 
The Radium King's Avatar
 
Join Date: Apr 2010
Location: Canada
Posts: 3,121
and transmission heating ...
The Radium King is offline   Reply With Quote
Old 07-03-2014, 11:58 AM   #6
Registered User
 
rdass623's Avatar
 
Join Date: Apr 2014
Location: new orleans
Posts: 249
the car bypass pipes are just fine unwrapped. the removal alone of the secondary cats will lead to cooler trunk temps (as mentioned above). additionally you would need to dismember a body to fit it into the rear trunk, so they will not be complaining about the temperature. the only real "advantage" I can see out of wrapping the cat delete pipes is the addition of a substance which will hold road salt and moisture against the pipes, enhancing the corrosive properties of both.
__________________
2005 Porsche Boxster S, 2000 Porsche Boxster 2.7L Base, 2000 Mazda Miata LS Supercharged, 2010 Toyota Tacoma TRD Off Road
Previous Vehicles: 2005 Ford Mustang GT, 1986 Alfa Romeo Spider, 1971 Alfa Romeo GTV, 1999 Ford Mustang
1977 Toyota Celica GT
rdass623 is offline   Reply With Quote
Old 07-03-2014, 12:02 PM   #7
Registered User
 
Pdwight's Avatar
 
Join Date: May 2013
Location: North Alabama
Posts: 2,079
Thanks Everyone

I was thinking while driving today that the pipes are not wrapped or shielded only the Cats...so I will not wrap them. Worst case I could always take them back off and wrap them.....Road Salt is not even an issue in Alabama ...besides I never drive this car in the snow (rare we even get snow) and rarely drive it in the rain.
Pdwight is offline   Reply With Quote
Old 07-03-2014, 02:57 PM   #8
Registered User
 
Coaster's Avatar
 
Join Date: Mar 2014
Location: Austin
Posts: 311
Garage
Is the ceramic coating a common process at muffler shops? Or, where do you get it done? Any idea on cost? Just curious.
__________________
2003 S, 6 Speed, PCM, PSM, Bose, Litronics with washers, on its' second LN IMSB, comfort top, UDP, 987 engine mount, 997 RMS, Koni Sport Shocks, H&R springs, Techno brace, comfort blinkers, nin8six windscreen, particlewave light up cubby
Coaster is offline   Reply With Quote
Old 07-03-2014, 03:11 PM   #9
Registered User
 
BYprodriver's Avatar
 
Join Date: Oct 2008
Location: O.C. CA
Posts: 3,709
Garage
Quote:
Originally Posted by Coaster View Post
Is the ceramic coating a common process at muffler shops? Or, where do you get it done? Any idea on cost? Just curious.
No, most busnesses that apply coatings specialize in that only. Go online to find a shop near you. Works much better if the part is new. About $70 for the secondary pipes inside & out.
__________________
OE engine rebuilt,3.6 litre LN Engineering billet sleeves,triple row IMSB,LN rods. Deep sump oil pan with DT40 oil.
BYprodriver is offline   Reply With Quote
Old 07-03-2014, 05:42 PM   #10
Registered User
 
rdass623's Avatar
 
Join Date: Apr 2014
Location: new orleans
Posts: 249
jet hot is a company who does the ceramic coating, I have friends who have used them before, but it is expensive. the cat bypass pipes are stainless (usually), there will be little gained from a performance or longevity standpoint. usually this process was used to prolong the life expectancy of mild steel headers which tended to rust out rapidly.

__________________
2005 Porsche Boxster S, 2000 Porsche Boxster 2.7L Base, 2000 Mazda Miata LS Supercharged, 2010 Toyota Tacoma TRD Off Road
Previous Vehicles: 2005 Ford Mustang GT, 1986 Alfa Romeo Spider, 1971 Alfa Romeo GTV, 1999 Ford Mustang
1977 Toyota Celica GT
rdass623 is offline   Reply With Quote
Post Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 04:42 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page