Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 04-11-2020, 06:55 AM   #5621
Registered User
 
Join Date: Mar 2013
Location: Gibraltar
Posts: 32
Garage
Quote:
Originally Posted by jcp View Post
Changed the RH outer tie rod end and the RH rear trailing arm today. That took care of the steering wheel shake and the bumping noises from the rear.
The trailing arm is ridiculously easy to change. After the car was raised, the tools gathered up and the rear wheel removed , the removal and installation of the link was less than 10 minutes.
Hi JCP, did replacing the rear RH trailing arm take care of an annoying rattling noise I have on mine when driving slowly over speed bumps etc.... ??? Thank you

Hurdi is offline   Reply With Quote
Old 04-11-2020, 07:34 AM   #5622
jcp
Registered User
 
Join Date: Nov 2019
Location: central okla
Posts: 86
It did on my car.
I had read a post about going over the same bump several times while changing loads against the suspension. Go over the bump with just enough throttle to maintain speed. Then go over the bump while lightly applying the brake, then do the same but apply bit of throttle. If the rattle changes intensity or goes away, then it's most likely a rear trailing link.
Good luck.

Last edited by jcp; 04-11-2020 at 07:42 AM.
jcp is offline   Reply With Quote
Old 04-12-2020, 04:25 PM   #5623
Registered User
 
Join Date: Oct 2018
Location: Evergreen, CO
Posts: 108
Quote:
Originally Posted by pilot4fn View Post
Installed new headers and downpipes with sport CAT's :dance:
Then went for a sprited 2 hour 'test drive' to the sunny twisties today


Well done. I ordered mine today. Did you have any issues with your O2 sensors?


Sent from my iPhone using Tapatalk
imhighlander is offline   Reply With Quote
Old 04-12-2020, 04:32 PM   #5624
Registered User
 
Join Date: Feb 2019
Location: Kernersville, NC
Posts: 291
Quote:
Originally Posted by imhighlander View Post
Well done. I ordered mine today. Did you have any issues with your O2 sensors?


Sent from my iPhone using Tapatalk
Same question about the sensor... and do you have a link?
__________________
1998 Boxster
2015 BMW M4 Dinan Stage 3
2016 BMW S1000XR
2015 Ninja 300
TTGator is offline   Reply With Quote
Old 04-12-2020, 10:11 PM   #5625
Registered User
 
Join Date: Jul 2019
Location: Finland
Posts: 306
Quote:
Originally Posted by imhighlander View Post
Well done. I ordered mine today. Did you have any issues with your O2 sensors?
Sent from my iPhone using Tapatalk
No issues at all. I have now driven approximately 600km and no issues at all. I used the old sensors in their respective places (before and after the CAT's).

Quote:
Originally Posted by TTGator View Post
Same question about the sensor... and do you have a link?
Here's from my previous post regading the connectors and extensions.

"Here's the part numbers I used to hunt the connectors:
Bosch 1-928-403-453
Bosch 1-928-403-736

Each cable needs one of each plug.

I purchased these from UK, since I'm in Finland (no customs etc issues) - at least untill the brexit kicks in
Here's the link where I ordered those both connectors:
https://www.auto-click.co.uk/1928403453
Same can be purchased from all continents.

On top of the cables I have the white 8mm heat resistant sleeve. This size fits real well ove the wires."


...and the actual post for the same:
What did you do with/to your Boxster today?

Hopefully this is helpful
__________________
Boxster 2.7 2001 Manual
pilot4fn is offline   Reply With Quote
Old 04-13-2020, 01:15 AM   #5626
Registered User
 
traveno's Avatar
 
Join Date: Aug 2019
Location: Oregon
Posts: 89
Garage
Got some more done today with my IMS project. I got the spoiler, rear bumper, exhaust, and various support bars from the underside of the car removed. Disconnected the CV axles from the transmission. The axles were being stubborn when I tried pounding them out of the wheel hubs. So, I called it a day there. Hoping to get that transmission dropped here real soon.
__________________
2001 Tiptronic S in Speed Yellow
traveno is offline   Reply With Quote
Old 04-13-2020, 05:16 AM   #5627
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
[ATTACH]22311[/ATTACH

Washed it.
Attached Images
 
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 04-13-2020, 03:04 PM   #5628
Registered User
 
Join Date: Feb 2019
Location: Kernersville, NC
Posts: 291
I made another DIY video when I painted the wheels of my Boxster 986. I also created a Patreon page if anyone is interested in supporting the channel and getting some additional content. You can join by going to www.patreon.com/helpmediy

https://youtu.be/yhbcD3t_pUI
__________________
1998 Boxster
2015 BMW M4 Dinan Stage 3
2016 BMW S1000XR
2015 Ninja 300
TTGator is offline   Reply With Quote
Old 04-14-2020, 04:08 PM   #5629
jcp
Registered User
 
Join Date: Nov 2019
Location: central okla
Posts: 86
Changed both rear control arms and the drivers side rear trailing arm today. The passenger side control arm proved to be quite a challenge. It refused to part company with the chassis (inboard end), taking the better part of an hour to work it loose. I rarely take a hammer to aluminum, but today was the exception.
jcp is offline   Reply With Quote
Old 04-16-2020, 03:27 AM   #5630
Registered User
 
Join Date: Jan 2019
Location: Houston, TX
Posts: 142
Bored during quarantine so added a bit of color to engine. Yes noone will see it except for you and me now.

Sent from my HD1907 using Tapatalk
rflores2323 is offline   Reply With Quote
Old 04-16-2020, 05:43 AM   #5631
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
Quote:
Originally Posted by rflores2323 View Post
Bored during quarantine so added a bit of color to engine. Yes noone will see it except for you and me now.

Sent from my HD1907 using Tapatalk
That looks interesting... keep going. When you've completed the painting fabricate the clear engine cover.

First, get that HAI covered.
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 04-16-2020, 11:47 AM   #5632
Registered User
 
Oldcarguy's Avatar
 
Join Date: Feb 2017
Location: North Eastern US
Posts: 646
What did you do with/to your Boxster today?

Finished my Pelican Parts headlight cover install. Very happy with the results. More pics in Pelican’s headlight cover thread.




Sent from my iPad using Tapatalk
__________________
Rgds, Fred
#317 550 Spyder Anniversary Edition 2004 Boxster S, 3.8L Flat Six Innovations engine, PSS9s, etc, etc . . .
The contents of my posts are for entertainment only. As confirmed by my many motor sports fails, I am not qualified to give product endorsements or mechanical advice
Oldcarguy is offline   Reply With Quote
Old 04-16-2020, 05:35 PM   #5633
Registered User
 
Join Date: Mar 2014
Location: So Cal
Posts: 299
Garage
Quote:
Originally Posted by M9G View Post
So in these times of lockdown, lets make the most of it.

Mopped and polished


I have those rims! 18"?
mgfranz is offline   Reply With Quote
Old 04-17-2020, 08:38 AM   #5634
Registered User
 
morgal48's Avatar
 
Join Date: Jan 2014
Location: Texas
Posts: 221
Started replacement of my a/c compressor clutch. Last time out I thought squirrels were wrestling behind me and today confirmed that the clutch pulley wobbles front to back and side to side. Found a clutch only assembly, refurbished, on a big auction site for much less than a new factory clutch assembly. Finding the clutch without the compressor attached was like finding hen's teeth - searched for a week. Thankful this is such an easy car to work on. Unlike the wife's Volvo. The Swedes are just mean.
__________________
2000 Boxster S
2010 Volvo XC60
2011 GMC Denali HD 6.6L (sold)
2008 Cayenne S (sold)
1989 Targa (sold)
morgal48 is offline   Reply With Quote
Old 04-17-2020, 03:53 PM   #5635
Registered User
 
Join Date: Oct 2018
Location: Evergreen, CO
Posts: 108
Started my weekend project.




Sent from my iPhone using Tapatalk
imhighlander is offline   Reply With Quote
Old 04-17-2020, 06:45 PM   #5636
Registered User
 
traveno's Avatar
 
Join Date: Aug 2019
Location: Oregon
Posts: 89
Garage
Quote:
Originally Posted by imhighlander View Post
Started my weekend project.




Sent from my iPhone using Tapatalk

I wish you luck! Taking old headers off are the only thing that gives me anxiety these days when it comes to wrenching on my cars.
__________________
2001 Tiptronic S in Speed Yellow
traveno is offline   Reply With Quote
Old 04-17-2020, 09:31 PM   #5637
Registered User
 
Join Date: Jul 2019
Location: Finland
Posts: 306
Quote:
Originally Posted by traveno View Post
I wish you luck! Taking old headers off are the only thing that gives me anxiety these days when it comes to wrenching on my cars.
Kudos to that!
I did the same project a week ago, but gave the header bolts change to my clocal Porsche indy. Too worried on messing up the aluminium heads...
__________________
Boxster 2.7 2001 Manual
pilot4fn is offline   Reply With Quote
Old 04-18-2020, 11:17 AM   #5638
Registered User
 
Join Date: Jul 2016
Location: Ireland
Posts: 153
Those header bolts are great fun. Hours of amusement to be had!
__________________
Traco
_________________
Older but no wiser.
2003 Boxster S, Seal Grey
Traco is offline   Reply With Quote
Old 04-18-2020, 01:19 PM   #5639
Registered User
 
fridsten's Avatar
 
Join Date: Aug 2015
Location: Stockholm, Sweden
Posts: 265
Not today, but a couple of days ago I had mine in the shop for a small service, new brake fluid and installation of a B&M short shifter. Huuuuuge difference!
fridsten is offline   Reply With Quote
Old 04-18-2020, 03:38 PM   #5640
Registered User
 
Join Date: Oct 2018
Location: Evergreen, CO
Posts: 108
Quote:
Originally Posted by pilot4fn View Post
No issues at all. I have now driven approximately 600km and no issues at all. I used the old sensors in their respective places (before and after the CAT's).



Here's from my previous post regarding the connectors and extensions.

"Here's the part numbers I used to hunt the connectors:
Bosch 1-928-403-453
Bosch 1-928-403-736

Each cable needs one of each plug.

I purchased these from UK, since I'm in Finland (no customs etc issues) - at least untill the brexit kicks in
Here's the link where I ordered those both connectors:
https://www.auto-click.co.uk/1928403453
Same can be purchased from all continents.

On top of the cables I have the white 8mm heat resistant sleeve. This size fits real well ove the wires."


...and the actual post for the same:
What did you do with/to your Boxster today?

Hopefully this is helpful
I'm still a bit confused. I installed headers and 200 cell catted midpipes today and the rear O2 sensors are too short. (NA spec 2004 986.2S (3.2) model). I'm afraid that if I splice in additional wire, the resistance won't be correct and I'll get CEL. Are there longer O2 sensors available that will connect? What are other people doing to run the post-cat O2 sensors on NA vehicles?

imhighlander is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 10:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page