Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Search Forums

Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: JSF95
Forum: Boxsters and Cayman Cars for Sale or Wanted 09-15-2024, 11:16 AM
Replies: 1
Views: 674
Posted By JSF95
2000 Boxster S for sale (bad engine)

Selling my 2000 Boxster S due to running out of room and time. My local indy shop diagnosed the engine with a bad rod bearing (can send vid upon request). Car still runs and drives. IMS and clutch...
Forum: Boxster General Discussions 07-29-2024, 06:31 PM
Replies: 0
Views: 106
Posted By JSF95
Debris in oil pickup w/rattle

Hello everyone.

My 986 had developed a rattling noise which I previously posted about...
Forum: Boxster General Discussions 07-11-2024, 06:36 AM
Replies: 5
Views: 408
Posted By JSF95
I have not checked timing. That requires...

I have not checked timing. That requires durametric software right? Car does not have any check engine lights.
Forum: Boxster General Discussions 07-10-2024, 05:27 PM
Replies: 5
Views: 408
Posted By JSF95
Nothing? Was really hoping someone had some ideas...

Nothing? Was really hoping someone had some ideas on what it could be...
Forum: Boxster General Discussions 07-08-2024, 06:16 PM
Replies: 5
Views: 408
Posted By JSF95
986 Boxster rattling noise w/out serpentine belt

My 2000 Boxster S has developed a rattling/clanking noise that I cannot seem to figure out. It is coming from the front of the engine area, but I have checked all the pulleys, compressor, pump, and...
Forum: Boxster General Discussions 12-22-2023, 12:29 PM
Replies: 2
Views: 538
Posted By JSF95
Well that’s not good! I couldn’t find anything...

Well that’s not good! I couldn’t find anything online about it either but figured someone must have done one at some point. I’ll check the Amazon stuff out
Forum: Boxster General Discussions 12-22-2023, 07:00 AM
Replies: 2
Views: 538
Posted By JSF95
6mm IMS studs size?

Hello all.
Doing the IMS on my 2000 Boxster S and I have ran into an issue! The stud size on the bearing is M6, not M8! The LN engineering tool kit uses the M8 thread on the hex bolt so it obviously...
Forum: Boxster and Cayman Parts for Sale or Wanted 10-06-2023, 03:58 AM
Replies: 1
Views: 523
Posted By JSF95
WTB: IMS Removal Kit

Needing to replace my IMS bearing and would like to purchase an IMS tool kit second hand if possible.
Forum: Boxster General Discussions 10-05-2023, 08:35 AM
Replies: 3
Views: 729
Posted By JSF95
3.2L swap into base 986

Hello All,

I have a 2001 Base 986 that has a cylinder with low compression (bad intake valve). I really dont feel like going thru the hassle of having the engine rebuilt, and since I am fairly...
Forum: Boxster General Discussions 07-15-2023, 01:04 PM
Replies: 0
Views: 377
Posted By JSF95
Restarting 986 after sitting

Hello all,
Just picked a 986 that has been sitting for about 9 months (outside unfortunately). Previous owner said it was running fine when he parked it last summer, with the occasional CEL for a...
Showing results 1 to 10 of 10

 
Forum Jump


All times are GMT -8. The time now is 02:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2025 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page