Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > DIY Project Guides

Post Reply
 
LinkBack Thread Tools Display Modes
Old 05-30-2018, 10:57 AM   #1
Registered User
 
Join Date: Jan 2014
Location: New Jersey
Posts: 1,631
Ideas for re-activating parking lights in converted headlights

I have a beautiful set of headlights that were converted to Fred's (Nine8Six) projector headlights by Particlewave. Despite the fact that the COB Angel Eyes were wired through relays, so that they operate in parking light only mode and turn off when the headlights go on, and I never drive with just the parking lights on, the Angel Eyes have still failed. This isn't a knock on anyone, this is just what happens when the COB Angel Eyes live next door to the hot projector beams in a machined aluminum casing.

What I plan to eventually do is restore the parking light function to my headlights. I would like to use the original parking light hole in the headlight unit. I don't want to add an LED light in the bumper grill or anything else external. The issue I have is that the wires for the high beam/low beam shutter in the projector unit are run through the old parking light hole. The Angel Eye wires also go through that hole, but they can just be snipped.

One option I have thought of is to use the original parking light sockets in the original holes. But that would involve removing the exterior headlight lenses to re-route the high beam/low beam shutter wires. I'm interested in any ideas that could be done without opening the headlights up.

Would it be possible to notch the original parking light socket so that it could still be inserted and not interfere with the wires going through the hole? Would the parking light melt the insulation on those wires being so close together? If so, could I use an LED light which runs cooler? I would still run the parking lights through the relays so that these lights only came on in parking light only mode and turned off when the headlights are on.

Any thought on this approach or other ideas would be greatly appreciated.

The good news is that I live in New Jersey and this isn't an inspection issue for me. The projector beam headlights are so superior to the original halogen headlights that I will stick with them. I'd just like to eventually get parking lights back.

As an aside, has anyone seen or heard from Fred/Nine8Six? His last activity on the forum was on November 14, 2017. I hope he is ok.

PaulE is offline   Reply With Quote
Old 05-30-2018, 01:02 PM   #2
Custom User Title Here
 
particlewave's Avatar
 
Join Date: Mar 2012
Location: Ft. Leonard Wood
Posts: 6,163
Garage
I would definitely not put an incandescent bulb next to those wires.

You could notch out a slot for the wires here and use an LED:



particlewave is offline   Reply With Quote
Old 05-30-2018, 05:37 PM   #3
Registered User
 
Join Date: Jan 2014
Location: New Jersey
Posts: 1,631
Awesome, thanks Particlewave!
PaulE is offline   Reply With Quote
Old 06-14-2019, 03:19 PM   #4
Registered User
 
Join Date: Jan 2014
Location: New Jersey
Posts: 1,631
Well I finally got around to re-activating my parking lights and disconnecting the dead Angel Eyes. I was able to re-route the black and red wires for the high/low beam shutter out of the hole for the parking light and through the small square hole under the old low beam hole where the projector is mounted. To do that, I removed the high beam, and snaked a thin stiff wire through the parking light hole and out the small square hole. To that wire, I attached a piece of 30 lb fishing line. Then I snipped the black and red wires and carefully taped them to a loop tied in the fishing line, and pulled the line out through the square hole, and the wires came with it. Then I reconnected the wires using low temperature butt connectors with solder in them. I heated them up with my heat gun on the low setting and held the joint wearing a heavy leather glove so that the heat gun didn't melt anything else.

To disconnect the Angel Eyes I used my small wire cutters and inserted them as far as possible into the parking light hole and cut them. I then cut off the ballasts so that I just had the blue and white wires, one coming off the relay and the other out of the headlight harness.

I wasn't able to rewire the old sockets I had for the parking lights. I got the terminals out of the sockets but couldn't get the crimps apart to get new wires in. So I found an almost identical socket with wires on eBay for $8 a pair and ordered them. They are just slightly shorter than the originals and fit right into the holes for the parking lights. I again used the shrink tube butt joints with low temperature solder and connected the 2 tails of the parking light sockets to the blue and white wires.

I now have parking lights that come on at the parking light setting of the headlight switch and go off when the headlights are turned on. It always makes me feel a little uncomfortable when I start cutting wires and think I know what I'm doing. Now that it's completed I'm feeling very self-satisfied that I was able to get this done without attempting to remove the outer headlight lens! Thanks to Particlewave for the original setup and advice that got me going. Here are a few pictures-











__________________
Current: 2022 718 Cayman GT4, PDK bone stock (the dark side).
Former: 2003 S, 3.6 LN Nickies, ARP rod bolts, under-drive pulley, Fabspeed sport headers, Softronic tune, 987 airbox 987 motor mount, Function-First Sport motor mount insert, Ben's short shifter, Nine8Six projector headlights & center caps, ROW M030, stainless flexible brake lines, B-K rollbar extension & fire extinguisher mount, hardtop
PaulE is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 06:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page