986 Forum - The Community for Porsche Boxster & Cayman Owners

		986 Forum - The Community for Porsche Boxster & Cayman Owners > Search Forums
Search Results

Garage

Page 1 of 2

Showing results 1 to 25 of 27
Search took 0.01 seconds. Search: Posts Made By: bachmoza

Forum: Performance and Technical Chat

09-20-2017, 02:37 AM

Replies: 18

Chain ramp replacement...gaining access?

Views: 5,615

Posted By bachmoza

Early or Later Timing chain tensioner, crank to IMS

These might be answers.

For Porsche 911 type 996 / 997 2001-2008, Boxster / Cayman 986 / 987 2001-2008:
PN 996-105-180-58, with big external spring,...

Forum: Performance and Technical Chat

07-31-2017, 11:13 AM

Replies: 14

Oil temperature sensor install

Views: 2,716

Posted By bachmoza

The length under the hex nut of 996 oil pressure...

The length under the hex nut of 996 oil pressure gauge and stock 986 oil pressure switch at passenger side were also short about 12.3mm(1/2 ").
AND the VDO temperature sensor installed was a bit...

Forum: Performance and Technical Chat

07-31-2017, 05:58 AM

Replies: 14

Oil temperature sensor install

Views: 2,716

Posted By bachmoza

I suppose the shorter one is just long enough to...

I suppose the shorter one is just long enough to be through into the oil circulating space. I don't know what is or are there underlying to interfere with the longer projected one.
The Pelican part...

Forum: Performance and Technical Chat

07-31-2017, 03:14 AM

Replies: 14

Oil temperature sensor install

Views: 2,716

Posted By bachmoza

My oil temperature gauge

Hope to help.
http://986forum.com/forums/show-tell-gallery/67509-my-center-console-vdo-gauges.html

My oil temperature sender is VDO from egauge.com: 323-055 - M14x1.5 - Screw - Single Channel...

Forum: Show and Tell Gallery

07-02-2017, 06:49 PM

Replies: 7

My center console VDO gauges

Views: 2,442

Posted By bachmoza

Yes. I will.

Yes. I will.

Forum: Show and Tell Gallery

07-02-2017, 06:16 PM

Replies: 7

My center console VDO gauges

Views: 2,442

Posted By bachmoza

My center console VDO gauges

Here is my oil pressure and temperature gauges in the dash DIN space.
Faceplate: Radio slot (DIN) or center console storage custom single-gauge aluminum panel from ebay seller 9xauto. ...

Forum: Performance and Technical Chat

06-30-2017, 04:53 PM

Replies: 7

S Oil cooler bottom hole sizes are different to non-S ?

Views: 1,901

Posted By bachmoza

WOW... Need_for_speed; Cool question! and...

WOW...
Need_for_speed; Cool question!
and vivid practical points drawn.
Risk of mixing oil with coolant! Scary to stand my hairs on end.

While ago I glanced at the Bentley's, removal...

Forum: Performance and Technical Chat

06-29-2017, 10:07 PM

Replies: 7

S Oil cooler bottom hole sizes are different to non-S ?

Views: 1,901

Posted By bachmoza

Photo added

http://986forum.com/forums/uploads02/Upper_surface_of_the_engine_block_underneath_of_the_oil_cooler1498802839.jpg

Forum: Performance and Technical Chat

06-29-2017, 09:20 PM

Replies: 7

S Oil cooler bottom hole sizes are different to non-S ?

Views: 1,901

Posted By bachmoza

Thanks.. So, whether the two hole sizes may...

Thanks..
So, whether the two hole sizes may be different or not, but those are destined to align in each hole center axis without leak issue?
Do you possibly remember what sizes of the new...

Forum: Performance and Technical Chat

06-29-2017, 04:21 PM

Replies: 7

S Oil cooler bottom hole sizes are different to non-S ?

Views: 1,901

Posted By bachmoza

S Oil cooler bottom hole sizes are different to non-S ?

Four underside hole sizes of S oil cooler(996-107-025-59) look all same to me on photos searched at Pelican. But for those of non-S cooler(996-107-025-07), two inner holes are definitely larger than...

Forum: Boxster General Discussions

04-06-2017, 04:38 PM

Replies: 0

Weird torque 80Nm for the automatic transmission oil pan fill plug?

Views: 1,012

Posted By bachmoza

Weird torque 80Nm for the automatic transmission oil pan fill plug?

80Nm( 59Ft-lb) is unarguable torque instruction found in all the water-cooled Porsche service manuals 2005-2009 Porsche 987.1 Cayman , Boxster 986 A86.00 Tiptronic -99 A86.05 00- A86.20 and 2005-2009...

Forum: Performance and Technical Chat

01-12-2017, 04:49 AM

Replies: 7

Inner tie rod removal

Views: 1,799

Posted By bachmoza

So, I understand that 1-1/4" crowfoot adapter of...

So, I understand that 1-1/4" crowfoot adapter of your tool worked. That is very helpful. Thanks.
And...
Counter-hold at sensitive steering rack or not,I believe, is another safety- pursuing step...

Forum: Performance and Technical Chat

01-11-2017, 02:14 AM

Replies: 7

Need to counter hold the steering rack on inner tie rod job?

Views: 1,639

Posted By bachmoza

Oh, thanks

Oh, thanks

Forum: Performance and Technical Chat

01-10-2017, 08:06 PM

Replies: 7

Need to counter hold the steering rack on inner tie rod job?

Views: 1,639

Posted By bachmoza

another Rennlist threads

Tie-rod / Steering - where to counterhold - Rennlist Discussion Forums (http://rennlist.com/forums/924-931-944-951-968-forum/823362-tie-rod-steering-where-to-counterhold.html)
Undoing tie-rod at...

Forum: Performance and Technical Chat

01-10-2017, 04:38 PM

Replies: 7

Need to counter hold the steering rack on inner tie rod job?

Views: 1,639

Posted By bachmoza

Gelbster, I could try that using 1-1/4" adaptor,...

Gelbster, I could try that using 1-1/4" adaptor, but the OEM TRW's flat inner end is octagonal and measured diameter of exactly 31.75mm(1-1/4"), so I think metric adaptor of 32mm will be fit which...

Forum: Performance and Technical Chat

01-10-2017, 02:50 PM

Replies: 7

Need to counter hold the steering rack on inner tie rod job?

Views: 1,639

Posted By bachmoza

Previous thread at Rennlist

Tie Rods; Counter Hold Rack??? Or no? - Rennlist Discussion Forums (http://rennlist.com/forums/928-forum/429188-tie-rods-counter-hold-rack-or-no.html)
http://members.rennlist.com/bigdave/TieRod.html

Forum: Performance and Technical Chat

01-09-2017, 10:29 PM

Replies: 7

Need to counter hold the steering rack on inner tie rod job?

Views: 1,639

Posted By bachmoza

Need to counter hold the steering rack on inner tie rod job?

Just before purchasing the universal Mayhew tool stated by the JFP months earlier..

Could I ask JFP or any gentlemen finishing this DIY? Do you recommend to counterhold the rack portion in the...

Forum: Performance and Technical Chat

01-09-2017, 08:36 PM

Replies: 7

Inner tie rod removal

Views: 1,799

Posted By bachmoza

Need to counterhold the rack portion?

[QUOTE=JFP in PA;501083]There really is no room for much of anything when working on the inner tie rod end. We use a Mayhew tool that slides over the tie rod and grips the inner flats, and it pops...

Forum: Performance and Technical Chat

09-16-2015, 08:38 PM

Replies: 41

Mid-Engine Cooling

Views: 5,637

Posted By bachmoza

Yup. Boxsters are rare, but Big brothers not..:(...

Yup. Boxsters are rare, but Big brothers not..:(

------------------
99 tip base, LN IMSB
Mazda MX-5 NB6C
Jaguar XJ3.2

Forum: Performance and Technical Chat

09-16-2015, 07:06 PM

Replies: 41

Mid-Engine Cooling

Views: 5,637

Posted By bachmoza

Thanks

Cool responses , and I'm getting more refined insights in our troubled lovely cars.
Thanks to gentlemen

Forum: Performance and Technical Chat

09-16-2015, 04:29 PM

Replies: 41

Mid-Engine Cooling

Views: 5,637

Posted By bachmoza

BYprodriver.. haha. Thanks

BYprodriver..
haha. Thanks

Forum: Performance and Technical Chat

09-15-2015, 09:47 PM

Replies: 41

Mid-Engine Cooling

Views: 5,637

Posted By bachmoza

Coming late, I'm curious about whether the taller...

Coming late, I'm curious about whether the taller oil cooler(S oil cooler, 996-107-025-59-M6) would be fitted to surrounding air inlet of the base pre-00 Boxster.
I got following reply today from ...

Forum: Boxster General Discussions

06-27-2015, 11:04 PM

Replies: 32

Poll: IMS: have you done it? (please make sticky)

Views: 4,121

Posted By bachmoza

Yes, LN IMSB dual row on 99 Tip, 57K miles...

Yes, LN IMSB dual row on 99 Tip, 57K miles showing cam deviation 3.

Forum: Boxster General Discussions

05-08-2015, 02:05 AM

Replies: 26

IMS Replacement

Views: 2,867

Posted By bachmoza

Retroman: - That is cool, lucid and all...

Retroman:
- That is cool, lucid and all possible measures. Thanks for reply.

Jake!

What an exquisite marvelous step!

Take off my hat to you!

CK

Forum: Boxster General Discussions

05-07-2015, 03:46 AM

Replies: 26

IMS Replacement

Views: 2,867

Posted By bachmoza

Anxious to hear from Jake!

+1,
I've already retrofit a LN dual row ceramic preemptively to my 99 tip a year ago. Could not wait without any promise for unanswered hope" IMS Solution for earlier double row engines"!
I...

Showing results 1 to 25 of 27

Page 1 of 2

All times are GMT -8. The time now is 10:50 AM.