DOF is here!
Just arrived. Bearing going in the freezer. http://986forum.com/forums/uploads01...1383845444.jpg
|
Nice! Let us know how the install goes and post some pic's!
|
How long do u think it will take u to install,seriously considering installing one myself,fairly mechanical.
I don,t need to change bearing just install the DOF on an 06 Boxster S. Any special tools i would need other than the standard stuff. |
Lots of pictures as this is going to be really interesting! Missed seeing you this summer when I was back there, we need to set up a time next year!
|
Pics to come. Eric - definately next time.
|
A quick update. I haven't had any time to work on the DOF much. I just installed the new steel dual row bearing. I must say it went in quite easy with out freezing it. Next is to pit the clip on it and get the grinder out and make the necessary adjustments to fit the new flange. I'll go snap a pic of the new bearing in the car.
|
Subscribed!
|
I only get about 45 mins here and there. Tonight I put in the bearing clip, made the notch for the dof and installed the dof. I used some permatex to make a tight seal, I nicked the gasket surface and didn't want to risk a leak. Lock righted the center nit and torqued it to its spec of 11ftlbs. Torqued the flange bolts also with the new bolts to 7.5 ftlbs. http://986forum.com/forums/uploads01...1384221859.jpg
http://986forum.com/forums/uploads01...1384221909.jpghttp://986forum.com/forums/uploads01...1384221963.jpg |
I notched it out slowly with a dremel, which worked very well. I smoothed it all out when done with a grinding stone. http://986forum.com/forums/uploads01...1384222075.jpg
http://986forum.com/forums/uploads01...1384222104.jpg |
Next step is to thread in the fitting into the dof. I thought I trimmed back enough bell housing but I didn't. Instead of unseating it and removing it I purchased a 5/16 24pitch Allen head plug from the hardware store so I can put that in its place and remove a little more material with out the threat of shavings getting into the dof. http://986forum.com/forums/uploads01...1384272401.jpg
|
Grinding complete, fitting fitted, tensioners re torqued and cam lock and crank pulley lock removed. http://986forum.com/forums/uploads01...1384287601.jpg
|
Nicework!!
|
You're almost there!
Good job. Happy Boxstering, Pedro |
Why is the case bolt above the IMS flange removed?
|
They are updated bolts. I figured I would update them while I was in there.
|
New name for the dof. Damn Oil Feed. I have a 987 airbox and let me tell you it's a pain in the you know what to get to the oil feed plug on the head. I'm not taking out the airbox so I now need to run to the hardware store to buy the one tool I seem to be missing, a 3/8 swivel. http://986forum.com/forums/uploads01...1384372340.jpg
|
The manual doesn't tell you that the plug is either a 5.5mm Allen head or a 6mm. Mine was a 6mm. I finally was able to pull it and get the new fitting in with an assortment of extensions and a swivel. http://986forum.com/forums/uploads01...1384445620.jpg
|
Quote:
I see you got a package with only one cam plug in it. I e-mailed Mike at TuneRS about this and he's going to start including two cam plugs in the future. One hint on the oil feed - thread the hose onto the oil feed plug first and get it most of the way tight, but not fully tight. Then put the oil feed adapter in the head. It should still rotate fine with the hose a little loose and you can get it tight. Then put the final tightening on the oil hose line. It can be pretty tricky to get the oil hose on the oil feed adapter once it's already in place. Putting the oil line on first makes it a much easier job - at least it did for me. Kirk Bristol |
Drilling a hole would have been nice. I am up to just tightening up the oil line on both ends. They are threaded already with no big deal. Thanks for all the advise though. It is a easy job to do as long as you are not afraid to get dirty and make a mess. :) I'm just hoping for no leaks after all is done. This was the first time I, myself have done a rear main seal and the DOF. I'm pretty confident it should all be ok though.
|
Quote:
Kirk |
All times are GMT -8. The time now is 07:15 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website