Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Performance and Technical Chat

Post Reply
 
LinkBack Thread Tools Display Modes
Old 09-29-2009, 04:27 AM   #1
Registered User
 
Join Date: Sep 2009
Location: Australia
Posts: 13
Fitting speakers into doors

Hi all Iwant to fit speakers into the doors of my 97 boxster have new door trims with speaker grills. Has porsche fitted the wiring as standard behind the standard none speaker door trims? If not will a later door loom with speaker wiring and door entery light fit into the door jam plug? If so is it wired to suit or can it be (dose it have vacant terminals to wire through it)?regards Peter

hatch1517 is offline   Reply With Quote
Old 09-29-2009, 02:07 PM   #2
Bob Hindson Racing
Guest
 
Posts: n/a
You probably won't have any wiring in place as a "pre-wire." BMW is much better than Porsche when it comes to this. Pulling new wire won't be terribly difficult, but certainly may become time consuming.
  Reply With Quote
Old 09-29-2009, 11:01 PM   #3
Registered User
 
Join Date: Sep 2009
Location: Australia
Posts: 13
Quote:
Originally Posted by Bob Hindson Racing
You probably won't have any wiring in place as a "pre-wire." BMW is much better than Porsche when it comes to this. Pulling new wire won't be terribly difficult, but certainly may become time consuming.
Thanks. Here in AU GM have wiring ready to plug into in the higher modles for cruise,fog lights,phone ect. Was just hopeing porsche was kind to there technissions (and save me some time ) thanks again
hatch1517 is offline   Reply With Quote
Old 12-18-2009, 04:28 AM   #4
Registered User
 
Join Date: Sep 2009
Location: Australia
Posts: 13
speakers into front doors 986

I have finaly fitted speakers into my doors 97/ 986. The door loom connector has vacant holes for extra pins I passed the speaker wirring splinto two threw two of them pulled the loom out of the door and used a thin welding rod feed threw rubber boot with the help of some silicon spray wasnt to hard just takes time.I used 996 door trims not sure of the modle had to change the door handle mount plate to fit the cable, the silver handel uses a diferent cable end but you can remove the plastic bush then remove some of the material from the bottom side of the hole so the cable clip can reach threw. Or of course use your old handle.
Thanks for the feed back.
hatch1517 is offline   Reply With Quote
Old 12-18-2009, 06:39 AM   #5
Registered User
 
Join Date: Sep 2009
Location: The City
Posts: 1,084
Garage
any pics? sounds like you had fun
Lobo1186 is offline   Reply With Quote
Old 12-19-2009, 04:40 AM   #6
Registered User
 
Join Date: Sep 2009
Location: Australia
Posts: 13
Sorry was to hot to think about photos most things like the plate to mount the speakers into the font doors I found on the net. There is a plug to pass the cables to fit the amp into the front boot behind the battery.Ran the rear speakers and sub wiring under the consol used a bose speaker box with 6 1/2 pioneer crossovers.6 1/2 in the doors and replaced the fronts with 4in alpines.It realy isnt a dificult job just time consuming.

hatch1517 is offline   Reply With Quote
Post Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 04:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page