Muffler swap

[nola911]

Couple hints...
1) Buy the boxster Bentley manual
2) Don't try to do it with the bumper on

It is very easy once the bumper is off. I tried twice with it on and spent more time busting knuckles than anything else. A shop would be intimidated by the swap unless it has done a boxster.

I wouldn't pay for it. It's an easy DIY and you learn a lot about the car when you do it yourself.

[John V]

There was a crossover point at which Porsche changed the mounting. On all "S" cars and 2000 and later non-S cars, it's easiest with the bumper on. For 1997-1999 cars, it's basically impossible to do with the bumper on.

I drop the exhaust fairly frequently for competition, and I have never once removed the bumper on my 2000 S. Piece of cake. Do not attempt on the earlier cars!

[D.L.]

Thanks for the reply. So, are you suggesting that it's worth having a shop do the swap for a nominal fee? Any other opinions out there in the 986 world want to chime in... please...

[Chris_Craft]

I did it recently on my 99, first with the bumper on then i did it the right way with the bumpber off. It is very easy. Would i have paid $100 for a shop to do it? Probably.

[John V]

Originally Posted by D.L.

Thanks for the reply. So, are you suggesting that it's worth having a shop do the swap for a nominal fee? Any other opinions out there in the 986 world want to chime in... please...

I would never pay for it. It's easy, doesn't take much time (especially if you have one of the later cars where you don't remove the bumper) and don't risk some goon at a shop screwing your car up.

[D.L.]

Okay.... so the stebro exhaust I ordered is coming in Monday. I have an earlier 98 boxster, so other than removing the bumper during the install, are there ANY other tips you guys can give me. I'm a little nervous to be honest.

I think the bumper removal will be okay, but there's not much information on removing the stock exhaust and installing the stebro. I tried looking for hours on this forum and renntech and there's plenty on how to take the bumper off, but not so much on actually removing the exhaust How many bolts are there for the exhaust, are some bolts hidden, is there a sequence in which bolts to take off first, do I need jack stands or a lift, do I need a second set of hands to help, etc.

PLEASE HELP before I take this on.

[John V]

The band clamps which fasten the muffler's u-tubes to the cats can get pretty rusty. I don't know if you re-use these with the stebro, but you might want to hit the bolts with some penetrating oil before tackling it.

I ended up trashing the stock bolts and using some quality stainless off-the-shelf hardware to replace them.

[der Geist]

I ended up trashing the stock bolts and using some quality stainless off-the-shelf hardware to replace them.

You can count on replacing these for sure. Mine were rusted so badly they all just broke off. It is super easy to do.

do I need jack stands or a lift

Anytime you get under a car you should have it on jackstands. NEVER get under a car without jackstands being firmly in place. Get a small floor jack and a good set of jackstands.

do I need a second set of hands to help, etc.

The stock muffler is pretty heft at 40+ lbs. It surprised me when I dropped it how heavy it was compared to the replacement. You should be fine on your own but it never hurts to have a spare set of hands.

If you are the least bit handy with a wrench you can do this. I would never pay anyone to do it.

[boxs2000]

Originally Posted by D.L.

Okay.... so the stebro exhaust I ordered is coming in Monday. I have an earlier 98 boxster, so other than removing the bumper during the install, are there ANY other tips you guys can give me. I'm a little nervous to be honest.

I think the bumper removal will be okay, but there's not much information on removing the stock exhaust and installing the stebro. I tried looking for hours on this forum and renntech and there's plenty on how to take the bumper off, but not so much on actually removing the exhaust How many bolts are there for the exhaust, are some bolts hidden, is there a sequence in which bolts to take off first, do I need jack stands or a lift, do I need a second set of hands to help, etc.

PLEASE HELP before I take this on.

I would go to the dealer prior and get a new set of the plastic screws/ tabs (3 of them) that hold the wing on. Most likely you will break these when you take it off in order to get to the bolts for the bumper cover. Otherwise, by taking the bumper cover off you are guarantee yourself to save some time and will not have to wish you were plastic man to get to the top bolts located on the top bracket. Also if no one his helping you, you may want to have a floor jack to support the exhaust as you line up the bolts and u joints on the installation also good to put it under the stock muffler as you remove it so that it does not fall on you. It's not a tough job, I have done it twice, once on my car and a 99. I also did a "euro bumper" hack while I had the bumper off by removing my rear bumperettes.

[Kirk]

>I would go to the dealer prior and get a new set of the plastic screws/ tabs (3 of them) that hold the wing on.


I've taken my rear bumper off a couple times and I didn't want to replace these plastic tabs each time. I ended up just tapping the thin sheet metal holes in the rear spoiler and using some nice, aluminum allen head bolts to hold the top of the spoiler in place. Personally I think it looks better and now it's easier to remove the spoiler. Although there's not much purchase for the bolts, it's enough for the application. Just a thought.


>I also did a "euro bumper" hack while I had the bumper off by removing my rear bumperettes.


Very nice man! Looks awesome and a nice, cheap mod. What kind of material did you use to cover the holes left from the bumperettes?