Anyone install LED day time running lights?

[bobd21]

Gang,

Has anyone self installed LED daytime running lights?

I saw the TechnoLite LED DRL kit that Pedro sells for $199 plus S&H: http://www.pedrosgarage.com/Site_2/TechnoLite_LED_DRL.html

It appears to be the same product as the iJDM product for $89:
http://store.ijdmtoy.com/Audi-A5-A6-LED-Daytime-Running-Lights-Driving-DRL-p/led_audi_drl_sku77.htm

It appears that it is an easy and simple install. Has anyone done this or found any other products that you recommend or suggest?

Thanks,

Bob

[Gary H]

$20 off ebay:

[Tranlm]

$20?!?!?!!? Link please?!?!?!

[Stroked & Blown]

Originally Posted by Gary H

$20 off ebay:

That is a creepy looking helmet/visor. Got any more pics of it?

[Gary H]

The Visor skin came from http://www.skullskins.net/

The DRLs in those pics were similar to these:

http://cgi.ebay.co.uk/DRL-8-LED-LIGHTS-E-MARKED-MAZDA-3-6-121-323-5-626-MX5-/300413246075?cmd=ViewItem&pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item45f2065a7b#ht_1701wt_1138


But I've now replaced them with Ring Automotives which are in a different league - pricey though!

[anti-bling]

Hey guys, long time lurker...first time posting. Here it goes...

i recently purchased some aftermarket led "DRL's"...im unsure as to what to hook the "hot" (red) wire up to. It should be a line that comes on when the ignition is on and off when the key is turned off...correct? Im pretty limited to whats under the hood. Any ideas?

[Jedi]

Hi Bob,

I was thinking of installing JDM LED DDL SKU68 lights on my 04 Boxster, just wondering if you did an install?

Thanks
Jim

[bobd21]

Hi Jim,

I bought the kit from Pedro and installed them myself. I am very pleased with it. They turn on when I start the car and look very stock. I get lots of compliments on them. It also helps to update the look of the car and is a safety precaution as day time running lights.

Here is what I bought and installed. http://www.pedrosgarage.com/Site_2/TechnoLite_LED_DRL.html

In case my attempt to attach or embed a picture does not work, here is a link to how it came out. My Car



Pedro send you complete instructions. He is also available to answer questions on the phone. I removed the front bumper cover, that was the most difficult thing to do, but there is a great video on YouTube that a gentlemen posted that shows you exactly what to do. Here is the link: http://www.youtube.com/watch?v=Um-h2aUJHY4 .

While I had the cover off, I also cleaned out the radiators as well. It is time consuming, it take me a good 5 or 6 hours, but I took my time and did everything slowly to get it done properly. I also used 3M double stick tape and zip ties to attach the lights and conceal the wires and everything else.

I was very pleased with it all and love the lights and results. To me it looks very stock and upscale. I did not want it to look like something a 16 year old put on his Honda Civic.

[Gary H]

Changed mine to larger Ring Automotive units, which go to half power automatically when you put on your headlights. (Also fitted a lower splitter and black mesh in the grills)

[chaudanova]

Here's mine... hard to capture how it really looks to the eye from the camera lens.. I'd say the picture isn't quite exactly how it looks in person, but here's a picture...

[heliguy]

Gary H. Where did you get the lower splitter?

[BrunoGT]

Originally Posted by Gary H

Changed mine to larger Ring Automotive units, which go to half power automatically when you put on your headlights. (Also fitted a lower splitter and black mesh in the grills)

Hello Gary,

First of all, congrats, the Ring Automotive units look great. My Boxster has the same grills on each side like yours. To fit the LED units, did you have to cut/alter the vertical supports of the grills? I'm debating between Ring Automotive (Vehicle Lighting, Bulbs, Lamps, Auto Electrical, Chargers, Battery Packs - Ring Automotive), Technolite from Pedro's Garage (TechnoLite LED DRL), and a cheaper option from eBay that has same dimensions as Ring Automotive, DRL W13 LED White 2X Slim Daytime Running Lights Fog HID Head SMD Power Xenon A | eBay. Thank you.

[Bobiam]

Really looks good. Can you provide some info about how they wire in? And the other front end mods are worth hearing about too.

[Jedi]

Hi bob,

Thanks for the reply, I order some lights from iJDMtoy.com. I think they have 8 lites per unit shouldn't look to bad. I viewed the bumper removal, I haven't desided where to run the wires yet or where to pull the power from, any suggestions? I was thinking maybe from the heated seat fuse as this fuse comes live when the key is turned on. I might not get at this for a while but will try to post results.

Thanks
Jim

[bobd21]

Jim,

I just sent you a private message with more information on how I installed them.

Regards,

Bob

[pacemaker1000]

copied from my thread on another forum




Although I did it when I had the bumper off you don’t have to if you follow this. I am not saying this is the correct way but it works. Follow at your own risk.
I have included links to Halfords just to give you an idea of items used.

The DRL’s used are from Halfords but seem to be some of the most popular on eBay just more expensive at £24.99. They also do a slightly larger version at £34.99 which use the same mounting bracket so take your pick or buy others.




You will also need:

5-6 m of wire if your lights didn’t come with any.


Some connectors assorted and fuse holder:



Down to work:

Remove the lights and thread some stiff cable or wire along the metal bumper between them:


Attach the DRL bracket to the underside of the air intake with the screws provided.



Pass the short wires from the DLR’s up to the light housing.
On the right side, as viewed from the front, tape the loose ends of your red and black wire to the stiff cable you put in and pull through to the other side. Leave about 12 inches spare and cut. Attach 2 red bullet connectors to the loose wires and attach to the DRL’s following the correct colour code which on these lights are plain black for earth and white stripe for red or positive


Leave enough slack to be able to remove the DRL’s in case you have to.
Do the same connections on the other side.
On the left of the car you should now have 2 red and 2 black loose wires. Strip these and twist the blacks and reds together and attach 1 blue male bullet to each. The females of these bullets will be attached later after the wires are connected to earth and 12v respectively.


Pass a red and black wire up the side of the light fixing and thread through the existing grommet used by the existing lighting wires


Crimp a ring connector to the black wire and attach to the earth bolt just the other side of the grommet. (Not sure if the one in the pack will fit, if not cut it to expand)


Continue with the red wire and pass through next grommet after removing the plastic cover next to the battery one. This is hard and you will have to make a new hole.


Just below the wiper arm is a black plastic cover, remove a couple of its screws (you may have to move the wipers to vertical and switch off). Drill a small hole the size of the wire as shown and thread the wire through. When you replace the screws the cover tightens over a seal and keeps it watertight)


Inside the car remove fuse box cover and pull though the red wire and attach to one end of your fuse holder.
You now need to attach this to a 12v that is only live when the ignition is on. Not having heated seats I had a spare position 6 across on the top row.
Attach a small male spade connector to the other end of the fuse holder.


Attach the female bullets under the light described above. Tidy up all wiring, tape to any existing wires or cables to prevent rubbing etc.

Feed the end through the top of the fuse box and plug in:


If you don’t have a spare fuse position (check as although I don’t have heated seats I still had a fuse in the position even though there was nothing on the other end of it). Then your best bet is going to get hold of a ‘fuse tap’. Google it there are different types and some will do away with the need for a separate fuse holder like this:



A lot of writing I know but I don’t see this job taking more than an hour or so to complete

Hope this helps

Pacemaker1000

[Guvs]

Hi All.
Sorry this might be a bit of a late thread to this post, but like Garry I have also put "Ring" DRL's on my Boxster, this is the thread I placed on my UK orientated Boxster forum:-

"Put my DRL in tonight, was pleasantly surprised as well, when after connecting them up to a direct feed from the battery, just to see how they looked (and if they worked ) they came on but went off after a few seconds, I thought I had a duff set, but I carried on with the wiring and when i contacted them through in line fuse to be on the safe side, they again only stayed on for a few seconds, but as soon as I started the car they came back on and have stayed on as long as the ignition is left on, and switches of when you turn the engine off. saves me looking for a switch, was going to get one from Cardiff Porsche £33 + vat, :lol not now:
So to answer a few questions
1. wire them up direct to your battery.
2. If you want them to dim down when you turn your side lights on , there is a wire there that you can connect up to your side lights.





This one is with side lights and fog lights on as well.





Here are a few photos of my Boxster.





Hope this helps someone.
Guvs.

[J Tinsby]

I passed another 987 the other day, dunno what year it was but it had LEDS on the front like my 2011 Base. His looked brighter than mine, I don't know if the "S" has more or brighter LEDS or if this was an aftermarket kit.

To get mine to come on I have to turn on the park lights they do not come on with the ignition.

[R33P]

[QUOTE=Guvs;243018]Hi All.
Sorry this might be a bit of a late thread to this post, but like Garry I have also put "Ring" DRL's on my Boxster, this is the thread I placed on my UK orientated Boxster forum:-

Hello, I have just seen your post and pics, your car looks really nice. I purchased a nice Guards red 04 Boxster a few weeks ago and fancy doing the wheels in black, like yours...did you have them shotblasted and powder coated?

The DLR kit looks spot on to, which lights did you use and how did you fix then to the front bumper? From reading your post, are you saying that you just connected them directly to the batter under the front bonnet or some wires in there?

Cheers
Craig.

[chipmunk]

Originally Posted by Guvs

"Put my DRL in tonight, was pleasantly surprised as well, when after connecting them up to a direct feed from the battery, just to see how they looked (and if they worked ) they came on but went off after a few seconds, I thought I had a duff set, but I carried on with the wiring and when i contacted them through in line fuse to be on the safe side, they again only stayed on for a few seconds, but as soon as I started the car they came back on and have stayed on as long as the ignition is left on, and switches of when you turn the engine off.

Guvs - I know this is an old post however I was wondering where you bought your DLRs from? I have seen relays that do what you describe but not a DLR unit that has this function built in.