Go Back   986 Forum - The Community for Porsche Boxster & Cayman Owners > Porsche Boxster & Cayman Forums > Boxster General Discussions

Post Reply
 
LinkBack Thread Tools Display Modes
Old 07-24-2019, 04:44 AM   #1
Registered User
 
Join Date: May 2019
Location: Guatemala
Posts: 2
Garage
Unhappy Tail Lights - having issues

Hey 986 lovers, greetings from Guatemala.

I am having an issue with one of my tail lights ( the drivers side ) ( the other one works fine ), only the hazard / stoplight / turn signal work. I cant have the fog light and tail light work. I recently bought a new “bulb holder plate “ thinking it could be some kind of contact issue, but the problem persists. Could it be a fuse issue? Cable issue? Any advice?

Bulbs Working according to picture :

A , B , E

Not working

C , D , F



986Guatemala is offline   Reply With Quote
Old 07-24-2019, 07:20 AM   #2
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
I see no "F" in the picture.

I'm guessing here.

Is your harness connection secure... tight... snug?

Is/are your front side-marker lights illuminated? Replace bulb(s) where applicable.

Have you checked the fuse for the lights? Replace fuse(s) where applicable.

Is bulb "D" good? Replace bulb if applicable.

Report back.
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 07-24-2019, 07:57 AM   #3
Custom User Title Here
 
particlewave's Avatar
 
Join Date: Mar 2012
Location: Ft. Leonard Wood
Posts: 6,163
Garage
Replace fuses A4 and A7 (for a layperson, visual inspection of a fuse tells you nothing about its condition).

If the issue persists, remove the headlight switch and clean the inner contacts (not the connector pins on the back) by spraying electrical contact cleaner into the switch and working the switch knob back and forth.
particlewave is offline   Reply With Quote
Old 07-24-2019, 07:17 PM   #4
Registered User
 
Join Date: May 2017
Location: West Mi
Posts: 164
I second the switch recommendation. I replaced mine this spring and all my tail light issues went away
MrBen is offline   Reply With Quote
Old 07-25-2019, 04:28 AM   #5
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
Quote:
Originally Posted by particlewave View Post
Replace fuses A4 and A7 (for a layperson, visual inspection of a fuse tells you nothing about its condition).

If the issue persists, remove the headlight switch and clean the inner contacts (not the connector pins on the back) by spraying electrical contact cleaner into the switch and working the switch knob back and forth.
Should I understand that even if the/a fuse looks good... no burnt connecter... that it could be bad? If an electrical problem persists (similar to the OP), and the/a fuse looks good... replace it anyhow?

Any other signs to look for if the/a fuse "looks" good?

Thanks!
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 07-25-2019, 09:45 AM   #6
Custom User Title Here
 
particlewave's Avatar
 
Join Date: Mar 2012
Location: Ft. Leonard Wood
Posts: 6,163
Garage
Quote:
Originally Posted by Starter986 View Post
Should I understand that even if the/a fuse looks good... no burnt connecter... that it could be bad? If an electrical problem persists (similar to the OP), and the/a fuse looks good... replace it anyhow?

Any other signs to look for if the/a fuse "looks" good?

Thanks!
Absolutely. A fuse can be bad, but look completely normal. You can test it with an ohmmeter (anything over 1ohm is bad, good should measure under 0.5ohms), but they’re cheap and it’s easier to just swap it out. If swapping doesn’t solve your issue, the fuse was likely fine.
particlewave is offline   Reply With Quote
Old 07-25-2019, 10:29 AM   #7
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
Quote:
Originally Posted by Starter986 View Post
Should I understand that even if the/a fuse looks good... no burnt connecter... that it could be bad? If an electrical problem persists (similar to the OP), and the/a fuse looks good... replace it anyhow?

Any other signs to look for if the/a fuse "looks" good?

Thanks!
You can also check without having to remove the fuses. Use a volt meter or a light probe with one end grounded. You can probe the fuses at the butt end. The butt (plastic) end of the fuses have tiny openings where you can probe each of the blades.




If you have power on both sides, the fuse is good!

Last edited by piper6909; 07-25-2019 at 10:41 AM.
piper6909 is offline   Reply With Quote
Old 07-25-2019, 10:41 AM   #8
Custom User Title Here
 
particlewave's Avatar
 
Join Date: Mar 2012
Location: Ft. Leonard Wood
Posts: 6,163
Garage
Yes and no. A test light is insufficient as you’d need to see the voltage drop from one side to the other to give an idea of resistance. You’d be surprised at how much a small voltage drop (slight increase in resistance) can affect some electronic components.

I just went through this yesterday with my sons friends car. Car wouldn’t fire, we determined that it wasn’t getting enough fuel, then tested power at the fuel pump. It was at 10V. Replaced the good looking fuse with new and it fired right up.

.

Last edited by particlewave; 07-25-2019 at 10:43 AM.
particlewave is offline   Reply With Quote
Old 07-25-2019, 10:49 AM   #9
Registered User
 
piper6909's Avatar
 
Join Date: Jan 2019
Location: PA
Posts: 1,531
Quote:
Originally Posted by particlewave View Post
Yes and no. A test light is insufficient as you’d need to see the voltage drop from one side to the other to give an idea of resistance. You’d be surprised at how much a small voltage drop (slight increase in resistance) can affect some electronic components.

I just went through this yesterday with my sons friends car. Car wouldn’t fire, we determined that it wasn’t getting enough fuel, then tested power at the fuel pump. It was at 10V. Replaced the good looking fuse with new and it fired right up.

.
Interesting. I thought fuses were either good or blown. I've never had such experience as you did. Unless there was a problem with the contacts. Did you try re-inserting the same fuse?

Either way, good to know!

Last edited by piper6909; 07-25-2019 at 10:51 AM.
piper6909 is offline   Reply With Quote
Old 07-25-2019, 10:52 AM   #10
1998 Boxster Silver/Red
 
Join Date: Sep 2017
Location: 92262
Posts: 2,915
Thank you for that info. I've no horn and the LEDS in the cubby aren't illuminating. Checked a fuse or two... but will employ your troubleshooting method, and without removing the fuse(s).

Thanks to the both of you.
__________________
1998 Porsche Boxster
Starter986 is offline   Reply With Quote
Old 07-28-2019, 09:10 PM   #11
Multi-Boxer Driver
 
Deserion's Avatar
 
Join Date: Nov 2010
Location: Orange Park, FL
Posts: 1,404
Garage


If your headlight switch is feeling a bit low on resistance or not clicking into each detent, may be time to replace it. This is what happens in higher temperature climates, and even being garaged too.

__________________
-Chris
2004 Porsche Boxster 2.7
1991 Porsche 911 C2 Targa 3.6
2017 Subaru Outback 3.6R
Deserion is offline   Reply With Quote
Post Reply

Tags
bulbs , rear lights , taillights


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -8. The time now is 07:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Pelican Parts Website -    DMCA Registered Agent Contact Page