Problem Finding First Gear

[maytag]

I didn't understand the original post the same way y'all did. I thought he was talking about something im experiencing in my 986 s right now, as well.
If I'm stopped, and particularly if I've been in neutral, when I go to 1st gear, it doesn't seem to want to engage fully. I frequently think it's in, lift the clutch only to hear a little grind, and no movement. If I try again immediately, it goes in fine.
I think it's a shift cable / shifter alignment issue. (Mostly because it started right after I installed Ben's short shifter)

Sent from my SM-G930T using Tapatalk

[Geof3]

Originally Posted by maytag

I didn't understand the original post the same way y'all did. I thought he was talking about something im experiencing in my 986 s right now, as well.
If I'm stopped, and particularly if I've been in neutral, when I go to 1st gear, it doesn't seem to want to engage fully. I frequently think it's in, lift the clutch only to hear a little grind, and no movement. If I try again immediately, it goes in fine.
I think it's a shift cable / shifter alignment issue. (Mostly because it started right after I installed Ben's short shifter)

Sent from my SM-G930T using Tapatalk

That could be dead fluid if you haven’t changed it recently, or more likely synchros going bad. Does 2nd grind or pop? It could be an adjustment thing, possibly even clutch, but the way you describe it sounds more like synchros to me...

[Daily Driver]

OP here. Let me try to be more descriptive. I had trouble selecting 1st gear when at a stop. I currently drive an E46 M3 with a short shift kit in it. I am familiar with 'tight gates' and the spring action of shifters.
The CS I drove had the 3rd/4th plane as the resting position; as one would expect. However, the difference/distance between 3rd and reverse was about 3/4" to 1". As a result, in trying to hit 1st, it was easy to select either reverse (if you pushed on the spring) or 3rd. On the other hand, the 5th/6th plane was over about 2" or 2 1/2" from the 3rd/4th plane - about where I would expect it to be. I could have become accustomed to where 1st was. The other CS I drove did not have this issue. Its shifter was exactly how you expect it to behave.
My question is whether or not this issue with getting into 1st can be adjusted, or whether it is a sign of a bigger shifter/cable issue.

[JBauer]

Originally Posted by maytag

I didn't understand the original post the same way y'all did. I thought he was talking about something im experiencing in my 986 s right now, as well.
If I'm stopped, and particularly if I've been in neutral, when I go to 1st gear, it doesn't seem to want to engage fully. I frequently think it's in, lift the clutch only to hear a little grind, and no movement. If I try again immediately, it goes in fine.
I think it's a shift cable / shifter alignment issue. (Mostly because it started right after I installed Ben's short shifter)

Sent from my SM-G930T using Tapatalk

I had to play with the alignment and cable adjustment on mine. In the installation video it says dont worry too much about the alignment but it matters. I originally had it close to perfect except 1st was a little tight and finding 3rd was hard sometimes. I took off the cables, loosened it up, realigned it and adjusted the cables a few times. No problems now. Goes through the gears perfect now. You might give it a shot.

[maytag]

Originally Posted by JBauer

I had to play with the alignment and cable adjustment on mine. In the installation video it says dont worry too much about the alignment but it matters.......
...... I took off the cables, loosened it up, realigned it and adjusted the cables a few times. No problems now. Goes through the gears perfect now. You might give it a shot.

Wait.... there's a VIDEO!?!?


Sent from my SM-G930T using Tapatalk

[JBauer]

Originally Posted by maytag

Wait.... there's a VIDEO!?!?


Sent from my SM-G930T using Tapatalk

Yep


https://youtu.be/38hER9ajgv0